Gates (clean tree, version single-source across FORGEFIRM_RELEASE /
rootfs stamp / .fw meta-version / tag, rootfs-vs-slot size with early
warning, installer-embedded pubkey must match the signing key,
factory-era fwup verification of the packed archive), then build,
pack, sign, checksum, and stage forgefirm.fw + sha256sums.txt +
forgefirm-image-glowforge.rootfs.wic.gz with the gh publish command
(--publish runs it where gh is authenticated). release.sh --dev packs
a dev-key-signed forgefirm-dev.fw from the release rootfs for the GUI
upload path. Signing keys are always passed explicitly - no defaults.
kas/README release order and the plan doc updated to match.
The image's fstab keeps the factory slots mounted under /factory, and
busybox mount's auto-type iteration against an already-mounted ext4
device provokes a cosmetic kernel 'Can't open blockdev' for each
foreign-type claim (reproduced and pinned on the bench: ext3-typed
mount of an ext4-held device prints it; ext4-typed does not). Probes
now reuse an existing mountpoint from /proc/mounts and mount fresh
targets with an explicit -t ext4.
Newer factory firmware's generic /etc/fw_env.config points at the
wrong device; its per-device /etc/fw_env_mmcblk2.config is the correct
one for the eMMC environment. The read-back verify caught the failed
write and aborted before the flip, as designed.
dd|gzip runs backgrounded while the installer prints compressed MB
every few seconds (old busybox dd has no status=progress); dd's exit
status is captured through a file so a device read failure is not
masked by gzip succeeding on truncated input.
Newer factory firmware (2024) has no /factory/imgN mounts and a
read-only rootfs, so slot probing and post-write verification mount
under /tmp, with the active slot read from the running root. The
target-slot unmount sweeps /proc/mounts (older firmware DOES mount the
slots). A failed ffboot download keeps an existing /data/ffboot
instead of aborting, so a local-.fw install works fully offline.
install-forgefirm.sh is now single-stage and never repartitions: run
from factory firmware, it archives every factory slot version plus the
recovery boot partitions to /data/forgefirm/archive (manifest with
md5s), verifies the signed forgefirm.fw against the embedded ForgeFIRM
pubkey (raw 32-byte form for the factory's fwup 0.14.2; dev key until
the production key ceremony), applies it to the INACTIVE slot with the
factory's own fwup, post-verifies the written rootfs, installs
/data/ffboot, and flips the saved env with read-back verification. The
booted factory slot stays installed and bootable; /data is untouched
beyond the archive. Fixed release asset name forgefirm.fw (version in
the fwup metadata and release tag).
slotmigrate (new recipe, rcS before mountall) reclaims the legacy
layout on eMMC-slot boots: deletes p4, grows p3 to the end of the
disk (sfdisk + partx BLKPG - works with a sibling partition as root),
then e2fsck+resize2fs. Every step is keyed off the actual disk state,
so interrupted runs resume and factory-layout disks are a no-op; SD
boots never touch the eMMC.
-l inventories every bootable partition (SD, eMMC slots 1/2, legacy
p4) as machine-parsable key=value lines: firmware type
(forgefirm/factory), version, kernel presence, booted/next markers,
plus the saved-env selection - the shared probe for the installer and
the forgectrl update manager.
Boot switching now writes all four selection variables (mmcdev,
mmchwpart, mmcpart, mmcroot) in one fw_setenv -s transaction and
read-back verifies, falling back from the libubootenv script format
to the classic u-boot-tools format to per-variable writes - the same
script works on factory firmware and ForgeFIRM. mmchwpart was
previously never set and a mixed env could survive a mid-flip power
cut. Switch targets must pass a content probe (rootfs mounts, kernel
present) unless -f. -e picks the newest factory slot by probing,
excluding slots occupied by ForgeFIRM.
The new ffboot recipe installs it as /usr/sbin/ffboot with
/etc/fw_env.config (factory-identical redundant env layout at eMMC
0x80000/0x82000) - previously the image shipped fw_setenv with no
config. Added to forgefirm-image.
The release image now targets the 200 MiB factory eMMC slot: content
plus 40 MiB working space, hard build failure past the slot size. The
raw ext4 is deployed alongside the wic; scripts/mkfw.sh packs it into
a signed .fw with factory-pattern upgrade.a/upgrade.b tasks. fwup
1.16.0 recipe (applies ForgeFIRM and Glowforge-signed archives on
device) is installed in both images. Dev images stay SD-sized with a
256 MiB working margin and no ceiling.
Verified on the 20260808153331 build: release ext4 180.8 MiB; signed
.fw applies byte-exact with fwup 1.16.0 and with the factory's 0.14.2
(raw-format pubkey), and 0.14.2 -V verifies the signature.
flow_confirm_drill.py walks the driver's suspicion/confirmation state
machine through every verdict with real pump-off transients in one M8
session; flow_escalate_drill.py exercises the starved-re-check
escalation against a short GFCOOL_CONFIRM_MAX_S. BRINGUP records the
triage resolution (the 2026-08-03 faults were a real transient
stagnation, probable pump airlock - the check was right), the slug/
circulation measurements, and the new check semantics.
The head lis2hh12 (i2c-3 0x1e, direct-I2C at ~530 Hz - st_accel sysfs one-shots are ~6 Hz and the kernel has no IIO triggers) sees rail contact as a 20-40x jolt over the creep baseline within ~4 ms. bump_seek.py: 3/3 detected hits, zero false positives over ~180 mm of creep, jog-cancel stop and back-off. BRINGUP carries the full record and the driver integration design.
Sources live at github.com/ScottW514/forgectrl (history extracted, layout src/ + init/); the recipe pins SRCREV and installs the init script from the repo. Adds the build-forgectrl.sh bench cross-compile script.
Adds the design matrix and its supporting tools, and records in BRINGUP
what the 60-run matrix overturned: sub-40-percent duty mimics flow
(three of five dead-pump trials looked healthier than a working pump),
the operating point and threshold now rest on 25 pooled observations,
periodic re-checks are thermally free with the fans running, and the
settle gate closes a bench-proven miss. Also records what is NOT yet
validated - warm-loop baselines and behaviour under laser heating - as
first-light commissioning items.
Records why the temperature formula changed (and that everything
derived from the old one had to be re-derived), the flow
characterization data at both heater duties, the false negative that
killed the dT-threshold design, and the downstream-rise check that
replaced it. Adds flow_characterize.py to the bench kit.
The UAPI raw->Celsius formula is an explicitly unverified best guess and
every absolute coolant threshold inherits it. temp_calibrate.py records
reference points (measured temperature paired with averaged raw ADC
readings) and least-squares fits the real line per sensor, printing it
against the guess with a difference table. Modes: watch / point / fit.
BRINGUP records the gate as complete with tach-verified results;
LIGHTBURN.md documents the per-layer Air Assist toggle driving the
cut-profile ventilation; fan_test.py joins the bench kit.
Scope on GPIO2_IO30 (the SoC FIRE drive): two 2.000 s FIRE windows,
the second terminated only by the SDMA end-of-data backstop. Measured
2.0000 s exactly with clean edges on BOTH termination paths - normal
completion and true underrun (streaming=1, kernel underrun state
reached and acked; fire_test.py gains the U mode). The backstop drops
FIRE within one tick regardless of how the stream dies.
With the waveform, stream-path, latch, topology, and interlock-
semantics results from earlier today, every standing hardware
verification gate for live fire is now passed; what remains is the
laser-milestone software and a chain-armed first-light procedure.
fire_test.py phases A/B with the scope on the PSU LASER_ON pin, power
byte 0 throughout, HV unpowered, operator-executed unlock: latch LOCKED
severs FIRE entirely (pin flat + kernel laser_enable 0 under 40k
streamed fire bits); latch unlocked with the chain unarmed shows FIRE
live kernel-side while the PSU pin stays flat - the factory board
gates LASER_ON behind OK_2_FIRE exactly like the OpenGlow AND design.
interlock_circuit semantics pinned by the 13-to-7 transition: b0
LASER_ON monitor active low, b1 FIRE active high, b3 latch 1=locked.
The 1-tick FIRE drop measurement is deferred (SoC net inaccessible;
PSU pin needs an armed chain) - documented with both closure paths.
Power-bytes-only program played by the pulse engine with the scope on
LASER_PWM: full duty staircase observed, run-start 100 percent duty
reset confirmed on the pin, consecutive-power-byte drop confirmed
(second byte of a back-to-back pair discarded), and duty persists
after end-of-data - the laser-off guarantee rests entirely on FIRE.
Zero motion (motor_lock=15 + no step bytes; position counters pinned)
and the laser chain silent throughout. Adds pwm_stream_test.py to the
bench kit and records the FIRE/OK_2_FIRE/LASER_ON/HV_EN naming from
the OpenGlow LASER SAFING sheet.
Direct PWMSAR duty steps with the machine in the locked state
(controller stopped, cnc disabled so steppers are unpowered, laser
latch locked, lid closed; laser_on_sampled stayed 0 throughout).
Measured on the pin: 25.0 us period / 40 kHz stable across the full
duty range; 50/25/75 percent confirmed visually; low end
cursor-measured 6.4 vs 6.3 percent commanded (PWMSAR=8), clean pulse.
Matches the register-level audit numbers (divider 13 x 127 counts).
Adds pwm_sweep.py / pwm_hold.py to the bench kit and records the two
remaining pre-live-fire gates (1-tick laser drop at underrun via the
stream path with FIRE observable under a locked latch; interlock
readback semantics) in BRINGUP.
The step backend now lives in github.com/ScottW514/grblHAL-glowforge
(grblHAL driver convention: core submodule, driver.c HAL, board header).
Add build-glowforge.sh, update the BRINGUP runbook (no -t throttle,
EEPROM path, kill-before-scp, producer stats line, reset/disconnect
semantics), and teach bench_m2.py to parse the F: status field (no
spindle registered = no FS: field). Settings-write crash fix is
upstream as grblHAL/core PR 999.
Extract the factory motion profile from the _RESOURCES pulse streams
(new puls_profile.py): 700/590 mm/s2 X/Y accel on v2.6.0 firmware,
202 mm/s travel peak at the 28160 Hz travel tick, PIC currents X 135/33
and Y 22/5 run/hold, decay mode 1. Add the bench_m2.py round-trip jog +
feed-hold suite (all green 2026-08-02: sustained 200 mm/s, exact
returns, clean hold/resume, zero underruns) and update BRINGUP.md:
board moved to a fixed lease at 172.16.1.97, analog config now applied
by the sink itself, $RST=$ note for stale stored settings.
BRINGUP.md is the cold-start reference: project status (audit phases
0-5 complete, Phase 6 spike achieved - first grblHAL-commanded motion
2026-07-26), bench/board access, build+deploy procedures, the step
backend runbook incl. the required analog machine config, the measured
hardware facts bank, and the ordered next-work list. scripts/bench/
preserves the hardware-verification tools (underrun feeder, end-of-
data protocol bench, PWM register check, cross-build scripts).
install-forgefirm.sh completed silently broken when the download, flash
write, mount or uEnv rewrite failed - add die() checks around every
critical step (audit N13/M12) and download the release asset under the
exact Scarthgap artifact name (forgefirm-image-glowforge.rootfs.wic.gz)
so uploads need no renaming. ffboot no longer depends on the never-
provisioned /etc/fw_env_mmcblk2.config: it falls back to
/etc/fw_env.config (which both the factory and ForgeFIRM images ship,
pointing at the eMMC env) and checks fw_setenv results (audit N16).
BUILD.md gets the real artifact name and marks the built u-boot
reference-only; INSTALL.md drops the stale script/ogboot names and the
cloud-connect promise, stating the image is bring-up-only (audit N11).
Replace the repo + default.xml + setup-environment workflow with kas:
- add kas/forgefirm-glowforge.yml (Scarthgap layers pinned, meta-openglow
as a local sibling) and kas/README.md
- remove default.xml, base/conf/forgefirm-bblayers.conf,
scripts/setup-environment
- .gitignore the kas-managed layers/ and build caches
- BUILD.md: kas host setup and build instructions
ScottW514