ScottW514
faaa6cb40b
Bump the grblHAL pin to the real-time producer change. Add motion.step-timing-under-load: the catalog had nothing that exercised step generation while userspace competed for the single core, which is exactly the gap that let the condition go unnoticed - the ring never runs dry, so cnc/underruns reads 0 through it. The test asserts the producer and the shipper both hold SCHED_FIFO, then drives 2000 mm/min round trips against a deliberate nice-5 CPU hog and requires the controller to report no clamped events. Add the pthresh live-fire drill: a constant-power ladder from 2 % to 30 % of full on scrap. Because $35 is a percent of full duty and the rungs are percents of $30 with $31 = 0, the lowest rung that marks reads directly as the $35 value. It needs $35 = 0 for the run, or the floor lifts every rung and hides the threshold. Record both open items in BRINGUP. The laser one carries the finding that the factory never uses duty as a power control - all five firing jobs in the captured pulse files pin the power byte at 127 and modulate dose by dithering the FIRE bit at 6.5-18.8 % density - so the captures cannot supply a $35 default, and the duty to optical-power transfer function of this supply has never been measured.
OpenGlow/ForgeFIRM Firmware for Glowforge
Open-source firmware for Glowforge brand CNC lasers. ForgeFIRM replaces the cloud-dependent factory software on the stock control board — no hardware modification — and gives the machine a local controller, a local web control panel, and a standard Grbl interface.
- Latest Release
- Installation Instructions
- Build Instructions
- Connecting LightBurn
- How motion and the laser are driven
- How cooling and airflow work
- The cameras and the video stream
- How the laser safing works
- How a release is accepted
- Community Support
What it does
Two controller modes, selected in the web panel and switchable while the machine is idle:
- GRBL mode — grblHAL runs on the machine and speaks Grbl 1.1 over TCP port 23, so LightBurn, UGS, and cncjs drive the laser directly. Motion runs on the board's own hardware step engine (SDMA + EPIT), fed live by the planner. M3/M4 dynamic laser power, coolant-flow verification, over-temp holds, and an operator button press to arm the laser for each job.
- Cloud mode — the machine presents itself as a stock Glowforge to the Glowforge web service, so the phone and web apps work as they always did. Optional, and off by default. GRBL mode jogs and cuts without it; the one GRBL-mode function that still reaches the Glowforge service is camera-referenced homing (below), until limit-switch homing lands.
Around both modes:
- A web control panel on port 8080: machine status and position, coolant and fan telemetry, safety-switch states, camera view, machine settings, hardware diagnostics, firmware updates, and boot-slot management.
- Camera-referenced homing:
$Hfrom any sender runs the factory-style camera homing cycle through the Glowforge service (a Glowforge account and a live service session are required for$H; everything else in GRBL mode runs without them), and the machine records where it is. - Cameras only capture with the lid closed. The lid camera faces the room once the lid is raised, so ForgeFIRM refuses every capture — live view, snapshot, and anything the Glowforge service asks for in cloud mode — until the enclosure is shut, and stops a running stream the moment the lid opens. See the cameras and the video stream.
Hardware
The control board is common to Glowforge Basic, Plus, and Pro. The 5 MP (OV5648) camera modules are fully supported and hardware-validated. The 8 MP (OV8856) modules found in "HD" units have a complete capture path — the kernel patches, device tree and sensor-aware capture profile they need are all in the build — but it has never run on an 8 MP machine, so treat it as untested; see the camera note in kas/README.md.
Safety
These machines contain a CO₂ laser: it burns, blinds, and starts fires. Never defeat the lid switches or interlock. Never leave a running job unattended — keep a fire extinguisher within reach. Read Before you cut — safety before your first job, and the Regulatory and legal section before installing. How the laser safing works describes the hardware safety chain and the software gates ForgeFIRM stacks on it.
A very important warning: this is experimental software. Use of this software could seriously maim or kill you or others, and voids your warranty. It is not affiliated with or endorsed by Glowforge. Use it at your own risk.