forgefirm/docs/CAMPAIGN-LOG.md

# ForgeFIRM campaign log

The dated record of how ForgeFIRM was brought up: bench campaigns, drills,
scope gates, the audit remediation, and the acceptance campaigns. Entries are
verbatim from the day they were written and are never revised — a correction is
a later entry, not an edit.

**Present state lives in [`BRINGUP.md`](BRINGUP.md)**, which is the runbook and
the authoritative list of open work. Read that first; come here for how a
result was obtained.

Two reading rules for this file:

- **Item numbers refer to the "Next work" list as it stood when the entry was
  written.** That list has since been renumbered around the closed items.
- **"above" and "below" refer to the document as it stood when the entry was
  written**, not to this file's arrangement. Later entries supersede earlier
  ones on the same subject; where an entry was proven wrong, the correction is
  further down.

## Before 2026-08-02 — platform bring-up

### Where the platform stood when the controller work started

**Platform bring-up: complete and hardware-verified.** Both motion blockers
fixed (cnc probe / 40v-supply; SDMA script relocated to `<26 0xF00>` with a
pre-run integrity guard); the end-of-data protocol reworked and bench-proven
(underrun is a first-class `underrun` state behind the `streaming` attr;
16/16 protocol bench); laser PWM verified at 39.98 kHz (register level);
`CONFIG_PREEMPT=y`; uEnv/u-boot/ulfius build integrity restored; legacy
cloud mode repaired (nvmem identity → fuse hostname verified;
deadman/safety loop; camera error paths).

**The controller spike: achieved.**
- grblHAL (unmodified core) runs on the board, speaking Grbl
  1.1f over **TCP port 23** (LightBurn-confirmed).
- Underrun proof: 100 kHz × 120 s under full load, 150 ms queue, 0.2 ms
  worst write latency, zero underruns. Measured SDMA script ceiling:
  **~165 kHz effective** (~6 µs/byte).
- **The step backend works**: the driver resamples grblHAL's step
  events into pulse bytes and live-feeds `/dev/glowforge`. X and Y jogs
  from TCP G-code move the real gantry; grblHAL and kernel position
  counters agree step-for-step. Motion-only: the laser latch is forced
  locked, byte bit 4 is never emitted.

## 2026-08-02 — motion quality, the scope gates, the cooling design

### First real LightBurn job

**First real LightBurn job: 2026-08-02, operator-verified.** Device
setup per `LIGHTBURN.md` (GRBL over TCP:23); a full design job — rapid
in, M4 dynamic-power cut trace at commanded speed, return rapid — ran
smoothly end to end on grblHAL-glowforge (laser locked, motion only).
Two driver fixes came out of the first attempts: the locked laser
spindle (M4/$32 support without fire capability) and the
continuation-wakeup cursor alignment (back-to-back cycles previously
clamped into step bursts — jerky, step-losing rapids; found via the
per-run `clamped` stat from the operator's own job log).

### Milestone 2 — motion quality

**Milestone 2 (motion quality): bench-verified 2026-08-02.** The factory
motion constants were extracted from captured factory pulse files
(`scripts/bench/puls_profile.py`) and applied end-to-end:
- grblHAL defaults now factory-true: 12000 mm/min max rate (X/Y),
  700/590 mm/s² accel (X/Y). Machine tick default 28160 Hz (the factory's
  own travel-move tick; 10 kHz caps an axis at 187.5 mm/s).
- The sink now applies the whole analog machine config itself at init
  (modes, decay, motor_lock, PIC currents) and switches PIC currents
  run↔hold around motion like the factory did (135/22 running, 33/5 idle,
  drop deferred until the kernel queue has drained).
- Bench (`scripts/bench/bench_m2.py`, all green): sustained 200 mm/s on a
  120 mm jog, exact round-trip positioning, feed-hold parks and resumes
  cleanly, current switching observed live, zero underruns at 28160 Hz.
- NOTE: stored $-settings beat freshly baked defaults — after changing
  `GLOWFORGE_DEFAULTS` values, run `$RST=$` once on the board (the sim
  persists settings in its eeprom file in /data).

### Backend milestone 2 closed

**Backend milestone 2 — motion quality: DONE and human-verified
2026-08-02.** Operator confirmed motion is "butter smooth" (and near
silent) on a full observation run — slow/fast/diagonal/zigzag jogs at
up to 200 mm/s under grblHAL-glowforge with the factory-true analog
config. The pre-tuning loudness was the 150/150 currents + unset
decay mode. Milestone closed.

### The standing scope gates

- **LASER_PWM waveform: PASSED 2026-08-02** (scope on the physical
  pin). Method: direct PWMSAR duty steps (`scripts/bench/pwm_sweep.py`
  / `pwm_hold.py`) with the controller stopped, cnc `disabled`
  (steppers unpowered), laser latch locked, lid closed;
  `laser_on_sampled` stayed 0 throughout. Measured: 25.0 µs period /
  40 kHz at every duty; 50/25/75 % confirmed visually; low end
  cursor-measured **6.4 % vs 6.3 % commanded** (PWMSAR=8) — clean
  pulse, no runts, carrier stable across the full range. Matches the
  register-level audit numbers (divider 13 × 127 counts, 39.98 kHz).
- **Stream-path power bytes: PASSED 2026-08-02** (scope on
  LASER_PWM, `scripts/bench/pwm_stream_test.py`: power-bytes-only
  program preloaded and played by the pulse engine; steppers
  energized but motor_lock=15 + zero step bits — position counters
  pinned at 0). Operator observed the full staircase AND both
  contract rules on the pin: **run-start duty reset to 100%**
  (first pulses would fire at full power unless the stream's first
  power byte precedes its first FIRE bit) and **consecutive power
  bytes dropped** (saw 25 % where a 75 % byte rode directly behind;
  75 % applied only after a spacer). Also measured: **duty persists
  after end-of-data** (PWMSAR retains the last value; the end-of-data
  backstop forces FIRE/step lines low, not the power setpoint) — the
  laser-off guarantee rests entirely on FIRE.
- **Laser latch + safety-chain gating: scope-verified 2026-08-02**
  (`scripts/bench/fire_test.py`, probe on the PSU-connector LASER_ON
  pin; power byte 0 throughout, zero step bytes, HV unpowered,
  operator at the power switch; phase B latch-unlock executed by the
  operator). Phase A (latch LOCKED): 40,000 streamed FIRE bits →
  pin dead flat AND kernel `laser_enable` stayed 0 — the latch
  severs the FIRE drive entirely. Phase B (latch unlocked, chain
  unarmed): kernel `laser_enable=1` mid-window, but the PSU pin
  stayed flat and `laser_on`/`laser_on_sampled` stayed 0 — the
  factory board gates LASER_ON behind OK_2_FIRE exactly like the
  OpenGlow AND design (FIRE ∧ OK_2_FIRE, active high at the PSU
  pin). **Interlock snapshot semantics pinned by experiment**
  (13→7 during the unlocked FIRE window): b0 = SoC-side LASER_ON
  monitor, active LOW (1 = not lasing); b1 = FIRE, active high;
  b3 = latch, 1 = locked/0 = unlocked.
- **≤1-tick FIRE drop at underrun/end-of-data: PASSED 2026-08-02**
  (scope on GPIO2_IO30, the SoC FIRE drive feeding the safing
  logic; `fire_test.py` B and U, operator-executed, duty 0, chain
  unarmed). Stream: two 2.000 s FIRE windows, the second ending
  exactly at end-of-data so its falling edge IS the SDMA backstop.
  Measured: **both pulses 2.0000 s exactly, clean edges, on BOTH
  termination paths** — normal completion (streaming=0) and true
  underrun (streaming=1, kernel `underrun` state reached and
  acked). The backstop drops FIRE within one tick (≤100 µs at
  10 kHz) regardless of how the stream dies.
  Signal naming (per the OpenGlow LASER SAFING sheet, confirmed to
  match the factory board): FIRE = per-tick request (kernel
  `laser_enable`, GPIO2_IO30); OK_2_FIRE = chain verdict; LASER_ON
  = FIRE∧OK_2_FIRE to the PSU; HV_EN = HV enable, safing-driven
  only.
- **ALL STANDING SCOPE GATES ARE NOW PASSED.** Live fire remains
  gated on the laser-milestone software itself (power-byte + FIRE
  emission in the stream engine with power-before-fire ordering,
  HV_WDOG retriggering only while genuinely cutting, M3/M4/$32
  mapping) plus a chain-armed first-light procedure; the hardware
  verification prerequisites are complete. Interlock-trip recovery
  (the one non-scope check that was left) was exercised in
  commissioning runs and closed 2026-08-12.

### Fan and thermal control

- **Fan/thermal control (operator-mandated laser-on prerequisite):
  DONE 2026-08-02, bench-verified** (test
  `scripts/bench/fan_test.py`). The policy described in this and the
  following bullets is the cooling engine's; it is now
  forgectrl `cool.c`, serving both controller modes, and the
  `GFCOOL_*` env names carry over as bench overrides (the conf keys
  are the `cool_*` ones — see the cooling-tunables note in the
  forgectrl section). Factory pulse-header
  values throughout: init = pump on / TEC off / purge on / idle
  fans (air assist 204); **M8** (coolant flood — LightBurn's
  per-layer Air Assist) = cut profile (air 1023, exhaust 65535,
  intake 43278); **M9** = 15 s cooldown (`GFCOOL_COOLDOWN_S`) then
  idle. Water temp polled at 1 Hz vs the ~31 °C factory run
  ceiling → one-shot controller warning (laser milestone upgrades
  it to a hard fire gate). Verified via tach readbacks: air tach
  period 4439→699 under M8, exhaust stopped→full, intakes ~3×,
  cooldown hold, clean return to idle; coolant temp visibly
  dropped during the blast. Absolute ceiling 33 °C (job-header
  CMrx).

### Coolant temperature conversion corrected

**Coolant temperature conversion CORRECTED 2026-08-02** — the
UAPI "best guess" `raw*-0.09653+94` was wrong (3–5 °C high, wrong
slope); the real one is the factory B-equation recovered from the
v2.6.0 binary (10 k B3380 NTC, 10 k divider, ×1.3 gain, 10-bit
ADC), proven by reproducing this machine's `WT*` cloud settings
exactly, and thermometer-checked to ~1 °C. Full derivation now in
`kernel-module-glowforge/UAPI.md`. Consequence: the 33 °C ceiling
had been firing at a real ~29 °C, and **anything derived from the
old formula had to be re-derived** — which is how the flow check
below got rebuilt.

### Coolant flow verification rebuilt on a 60-run design matrix

**Coolant flow verification — REBUILT ON A 60-RUN DESIGN MATRIX
(2026-08-02 overnight).** Everything below supersedes the earlier
ΔT-based designs; the tools are `scripts/bench/flow_matrix.py`
(+`flow_sampler.py` on the board), `flow_sustained.py`,
`flow_warm_validate.py`, `flow_recheck_char.py`.
- **Duty is the decisive parameter.** Below ~40 % the stagnant
  loop sheds the heater's output by natural convection well enough
  to **mimic flow**: at 30 %/50 s the five pump-stopped trials read
  8.15, 8.69, 8.78, 12.25, 13.33 °C while flow never exceeded 9.08
  — three of five dead-pump cases looked *healthier* than a working
  pump. At 40 % heat input outruns convection (flow ≤11.46,
  no-flow ≥16.04, d′ 8.4) and it is also the cheapest viable
  option (~0.8 °C of loop heating per check vs ~2.0 °C at 50 %).
- **Operating point: 40 % duty, 50 s window, threshold 14.4 °C**
  (balanced midpoint of 17 flow observations peaking at 12.75 and
  8 no-flow observations bottoming at 16.04).
- **Periodic re-checks every 150 s** (`GFCOOL_RECHECK_S`), because
  a stopped pump is undetectable any other way — absolute
  temperature only tracks a *circulating* loop, and "coolant
  should warm while cutting" is ambiguous (a light engrave may add
  no measurable heat). Sustained 40-minute run: zero false faults,
  and **no thermal accumulation** — with cut-profile fans the loop
  *cooled* 2 °C while being interrogated throughout.
- **Settle gate (safety-critical).** The check measures a rise
  from a baseline; capturing that baseline while the loop is still
  cooling from earlier heat produces garbage and was bench-proven
  to **miss** (reported flow with the pump stopped). Checks are now
  requested, and start only once the sensors agree **and** the
  downstream reading is stationary. Stationarity uses a
  **split-half mean difference**, not peak-to-peak: measured noise
  on a settled loop is 0.52 °C p-p (0.70 worst) but only 0.11 °C
  split-half (0.21 worst), so any p-p threshold tight enough to
  catch drift sits *below the noise floor* and the gate never
  opens.
- **Record: 25/25 correct classifications at 40 %**, plus all three
  settle cases (settled/flow, settled/no-flow, and the unsettled
  no-flow case that previously missed → now defers, then faults).
- **NOT YET VALIDATED (first-light commissioning items):** all
  baselines were 19–23 °C (an overnight-cool room; the loop
  equilibrates near ambient and the heater cannot reach a
  cutting-session loop temperature — 100 % duty drives the
  downstream sensor past 50 °C in 30 s while the bulk barely
  moves). Behavior at 27–32 °C baselines, and under real laser
  heating, must be characterized at first light. Physics argues
  the dependence is weak — with forced flow ΔT = P/(ṁ·c), which
  carries no absolute-temperature term — but that is reasoning,
  not measurement.

### Coolant flow verification — the superseded first design

*(Superseded earlier text kept below for context.)*
**Coolant flow verification (first attempt, live-verified both ways).**
Continuous 10 % heating was never viable on the corrected curve:
flow ΔT ≤3.69 vs no-flow ΔT ≥3.74 — a 0.04 °C gap against ~0.9 °C
of sensor noise. At 30 % the ΔT bands separate (≤9.32 / ≥10.99)
but a ΔT threshold still **failed a live pump-off drill** (8.8 °C
vs a 10.2 °C limit), because a check starting from a cold heater
never reaches the steady-state delta. Final design: a **one-shot
check at job start (M8)** — heater to 30 % for 50 s — with the
discriminator being **downstream temperature RISE** (flow ≈10.3 °C
vs no-flow ≈15.1 °C, ~6 °C separation; threshold 12.7 °C,
`GFCOOL_FLOW_RISE`). Heater goes off afterwards, so the loop is
not warmed for the rest of the job, and absolute over-temp
monitoring carries protection from there (a pump failure mid-cut
shows as a temperature climb far faster than any heater delta).
Verified twice each way from a cooled loop. **v2 (same day): heater job-scoped** (M8..M9 only — an
always-on heater eats headroom below the 31 °C start gate at
idle; flow faulting arms 30 s after heater-on), **two-phase
cooldown** (15 s smoke clear at run duty, then half-duty airflow
until the upstream temp is under the 31 °C resume gate or
`GFCOOL_COOLDOWN_MAX_S`), and **factory-style over-temp pause**
using the factory coolant windows (run ceiling 33 °C / resume
31 °C, env-adjustable: `GFCOOL_TEMP_MAX`/`GFCOOL_TEMP_RESUME`):
a CYCLE over the ceiling gets a feed hold + forced cooling
airflow + auto-resume on recovery; a JOG gets a jog-cancel
(grblHAL refuses HOLD from the jog state by design). Senders see
the Hold state and [MSG:Warning:…] lines. Drilled live with test
limits: jog canceled mid-move, cycle held and auto-resumed, fan
profiles restored on stand-down. TEC control remains for the
laser milestone; these warnings/holds become hard fire gates
there.

## 2026-08-03 — the camera service

### Bench record

Bench (2026-08-03, on the board): stream **15.0 fps** sustained at
1296×972 (NEON demosaic + VPU encode; 3.2 fps on the full software
fallback);
full-res snapshot 2.4 s warm / 2.7 s cold (cold includes the pipeline
bring-up); two parallel same-camera clients share the frame rate; idle
teardown observed. Borrow verified: head snapshot 200 during a lid
stream, the stream riding through the ~1-2 s gap. Preemption verified:
a head-stream request ended the lid viewer's stream cleanly (curl exit
0 mid-stream) and was serving head frames within ~2 s; switching back
likewise. **Motion coexistence proven**: X
round-trip jogs at F1200 with an active stream — producer stats
`clamped 0`, max behind 4.5 ms (the daemon runs at nice +5, single

### LightBurn consumes the stream

**LightBurn consumes the stream directly — operator-verified
2026-08-03** ("without issue", via the mjpg-streamer-compatible
`/?action=stream` alias) while jogging the machine from the same
LightBurn session.

### VPU JPEG offload

**VPU JPEG offload: DONE 2026-08-03, bench-verified — 7.9 fps** (2.5×
the software rate). The stream path demosaics the 2×2 superpixels
straight to planar YUV420 (JFIF full-range 601) and the **CODA960 VPU
JPEG encoder** (mainline coda, V4L2 mem2mem; found by personality, not
node number) does the encode: per-frame **copy 43 ms + convert 75 ms +
encode 7 ms**. Two hard-won facts:
- **Coherent V4L2 MMAP capture buffers are uncached** — demosaicing
  in-place out of one costs ~340 ms/frame at this resolution; one bulk
  memcpy into a cached bounce buffer first (43 ms) makes the same
  demosaic run in 75 ms. The bounce copy is now the fallback path only —
  non-coherent (cached) capture buffers (below) are the default on the
  patched kernel, and all camera paths read the capture buffer directly
  through them.
- The VPU encoder accepts 1296×972 exactly (no MCU-alignment padding
  needed) with quality via V4L2_CID_JPEG_COMPRESSION_QUALITY.
- **A CSI noise/glitch frame can out-size the coda driver's default
  ~2 B/px JPEG capture buffer** (kernel logs "JPEG too large for
  capture buffer" + a vb2 WARN; observed once under streaming+motion
  load). forgectrl requests 3 B/px and drops error-flagged dequeues as
  single bad frames — hardware encode stays active; software fallback
  engages only on repeated consecutive hard failures.
libjpeg remains the automatic fallback (`FORGECTRL_NO_VPU=1` forces
it) and the snapshot path; `/cam/status` reports `"encoder"`.

### NEON demosaic

**NEON demosaic: DONE 2026-08-03 — 15.0 fps, sensor-limited.** The
YUV420 superpixel convert has a NEON kernel (vld2q deinterleave,
vrhaddq greens, vmlal/vrshrn luma, vpaddlq block sums for chroma;
`FORGECTRL_NO_NEON=1` forces scalar): convert 75 → 18 ms, per-frame
copy 34 + convert 18 + encode 7 ≈ 59 ms against the sensor's 66 ms
frame period. The NEON and scalar paths are bit-identical — proven on
a live frame via `FORGECTRL_NEON_CHECK=1` (one-shot memcmp, logs
IDENTICAL). Motion coexistence re-proven at 15 fps: jogs with an
active stream show clamped 0, max behind 7.2 ms (~4 % of the 200 ms
queue) — the worst-case contention signature so far; if real jobs
ever clamp, a stream-fps cap knob is the relief valve.
The IPU cannot help with demosaic (its IC is CSC/scale only — the
`imx-csc-scaler` at /dev/video8 matters only for a future full-res
stream). Not yet done: lens calibration / bed alignment (the
fisheye needs LightBurn's camera calibration pass), and the deferred
5.6 emulator homing-image smoke (the cloud emulator can now be pointed
at live snapshots).

### Cloud-mode complete review (operator-directed)

**Cloud-mode complete review** (operator-directed 2026-08-03):
`load_motion` preloads a job's ENTIRE pulse file into the ring with
no backpressure recovery — with the 16 MiB default ring that caps
cloud jobs at ~28 min and a too-big job fails mid-download; the
write path needs rework (stream-during-run or graceful
too-big rejection). Also: a marked TODO in `load_motion` copies
every job's full pulse file into the logging directory (disk
filler), and many cloud actions are not currently handled at all —
review the action surface end to end (gfutilities service layer).

## 2026-08-07 — pacing, the fortify crash, cached buffers, homing

### Protocol-loop pacing is fd-blocking

**Protocol-loop pacing is fd-blocking (2026-08-07).** `serial_wait()`
drains TX then `ppoll()`s the listen/client fds with the
state-dependent timeout (idle/alarm 10 ms — 1 ms while a delay
callback is pending — motion 200 µs), so traffic wakes the loop
instantly while idle ticks stay coarse. **Bench-verified: idle CPU
7–12% → ~2%** (1.95% with the camera streaming beside it), status
RTT ~1.0 ms median, jogs exact, `clamped 0` with an active stream.
Client RX is armed only while the ring has a full read's worth of
room, so a flow-control-violating sender is paced, not spun on.

### Fortify overflow fixed in the core

**Fortify overflow fixed in the core (2026-08-07): images before this
fix boot with a DEAD controller.** The Yocto-built binary (compiled
with `-D_FORTIFY_SOURCE`) aborted at `settings_init` — "buffer
overflow detected" in /data/glowforge.log — before serving: the core's
`step_us_min[4]` holds `ftoa(hal.step_us_min, 1)` and our 28160 Hz
stream tick renders "35.5" (5 bytes). Bench builds (no fortify)
silently truncated the adjacent unit string instead, which is why it
never showed on the bench. Fixed by sizing the buffer (the single
local commit the core fork's `forgefirm` branch carries atop upstream
master); `$ES` now reports `[SETTING:0|…|35.5|…]` intact. Repro/diagnosis path if ever needed
again: `scripts/bench/build-glowforge.sh` variant with
`-D_FORTIFY_SOURCE=2`, gdb `set breakpoint pending on` + `break
__chk_fail`, run on the board. **Whole-image boot verified 2026-08-07
on the flashed 20260807214320 SD**: both services autostart from the
image binaries — grblHAL (fortified) serves at 1.0 ms RTT with exact
jogs, $0 min 35.5 intact, $H rejected ($22=0); forgectrl streams
15.0 fps, `"buffers":"cached"`, vpu, 41% CPU; grblHAL idle 2.1%.

### Non-coherent (cached) capture buffers + stream FPS cap

**Non-coherent (cached) capture buffers + stream FPS cap: DONE
2026-08-07, bench-verified on the flashed patch-0010 image.** The
remaining per-frame CPU cost was the ~34 ms bulk copy out of the
uncached V4L2 MMAP buffer. forgectrl REQBUFS with
`V4L2_MEMORY_FLAG_NON_COHERENT`; kernel patch 0010 (meta-glowforge-bsp
linux-fslc, `allow_cache_hints` on the imx capture queue) makes vb2
honor it — CPU-cached mmaps with the cache invalidate done inside
DQBUF — so the demosaic reads the capture buffer in place and the
bounce copy disappears. **Bench (2026-08-07, flashed image): stream
stats `dqbuf 0 ms, copy 0 ms, convert 19-20 ms, encode 7 ms` (the
invalidate is sub-ms in practice), 15.0 fps sustained, daemon 41.5%
CPU with one viewer vs ~66% on the bounce path** — per-frame CPU
roughly halved (~27 ms vs ~60 ms busy). Full-res snapshot through the
cached path visually verified (clean fisheye bed image, live frames
differ). Detection is by the `MMAP_CACHE_HINTS` capability bit: on a
kernel without patch 0010 the daemon falls back to the bounce-copy
path unchanged — **fallback bench-verified 2026-08-07 on the
unpatched kernel** (copy 35 ms / convert 18 / encode 7, 15.0 fps, vpu
— identical to before). `/cam/status` reports
`"buffers":"cached|uncached"`; `FORGECTRL_NO_CACHED_BUFS` forces the
bounce path for A/B; the stats log line includes the DQBUF time.
`FORGECTRL_STREAM_FPS` caps the stream rate — capped frames are
requeued without demosaic/encode (snapshots still ride on them) and
don't count toward fps — **bench-verified 2026-08-07**: cap 5 →
5.0 fps exact, daemon 23% CPU vs ~66% uncapped (bounce path; the
relief valve if future CPU work needs headroom). Default stays sensor
max. Images from 20260807204056 carry forgectrl at the bumped SRCREV
(73283b6), so a fresh burn ships the right daemon.

### Web-service homing: bench record and live verification

- Bench record 2026-08-07: forgectrl `/settings` verified on the
  board; `$H` mode dispatch verified (none → error 5); a stub
  gfcloud session (`gfcloud_home_cmd = /bin/true`) completed the
  full real-device handover — `H:1`, MPos set — and post-resume X
  jogs ran the gantry clean (clamped 0). Host tests covered
  success, calibrated coords, runner-failure and timeout-kill.
- **LIVE gfcloud homing VERIFIED 2026-08-07 (bench, via `$H`):**
  full sequence in 65 s — hunt (Z hall + hunt puls), lid image,
  corner move (head physically to back-left), confirmation lid
  image, quiet detect, final Z re-reference — `ok` +
  `<Idle|MPos:0,0,10.593|H:1>`, stream resumed clean. The FIRST
  live attempt failed and exposed four real bugs, all fixed the
  same day:
  1. gfhardware `_run_loop` halted every motion ~0.1 s in on a
     false SW_ESTOP trip — the estop sense reads low during any
     motion (facts bank in `BRINGUP.md`). Gate is now opt-in
     (`MOTION.ESTOP_HALTS_MOTION`, off in gfhome.conf).
  2. `cnc.halt()` didn't exist → the halt path crashed →
     deadman fd closed mid-run → real kernel e-stop (40V off,
     every later hunt skipped as 'Disabled').
  3. Camera conflict: gfhardware's direct V4L2 grab fails while
     forgectrl serves a stream (LightBurn holds one); the runner
     now captures via forgectrl `/cam/snapshot` (full-res, mux
     borrow, per-shot `lamp=` override — head images torch-off).
  4. Kernel: the deadman e-stop path ran sync SPI (PIC safing)
     inside the ATOMIC dms notifier chain → RCU splat. Chain is
     now blocking (trip point = pulsedev release, process ctx);
     the panic handler keeps only the atomic motion stop.
  Also mapped kernel state 'underrun' in gfhardware (state polls
  raised ValueError on it). Commits: gfhardware 8aa4a49 (+02e66c6
  `_hunt` offset), forgectrl 0b05e48, forgefirm cc838f1,
  kernel-module 5fa558c — board runs all of it (module hot-swapped;
  gfhardware hot-patched over the pinned package). All repos are
  pushed and every recipe pin is bumped to these revisions
  (forgefirm 2dce136, meta-openglow 9e2aa34; recipes
  bitbake-verified from the new pins), so a fresh image build
  carries the whole homing release. Remaining homing polish:
  calibrate `gfcloud_home_x/y` against a jog to a known reference
  if the factory corner offset matters.

## 2026-08-08 — diagnostics, panel rework, wireless, install/update

### Diagnostics bench record

Bench record 2026-08-08 (hot-deployed binaries, all through the HTTP
API): **conf plumbing** — `cool_flow_rise=8` posted, next M8's healthy
check read `limit 8.0` → SUSPECT; key cleared mid-session, next M8
re-read 14.4 and the confirming pass cleared the suspicion (also
proving episode continuity across M9/M8). **Takeover** — during a
running verify: grblHAL process gone, marker present, settings POST
409, second start 409. **flow-verify PASS** in 2:42: flow 11.4
(dT 9.7) / threshold 14.4 / no-flow 17.6 (dT 12.8), margins +3.0 and
+3.2; controller back (fresh pid), marker removed, heater 0, pump on
after. Validation ranges live-checked (rise 0.5 → 400, pct 101 → 400,
confirm 45 → 400). UI browser-verified mid-run: Diagnostics panel
streaming phase/temps/log with the lock banner up, Machine tab
Cooling card showing defaults as placeholders, inputs disabled.
**flow-calibrate COMPLETE in 8:45**: flow band 11.6/12.0/12.0
(max 12.0), no-flow band 17.6/17.7/18.1 (min 17.6), gap 5.7 →
**recommended 14.8 — within 0.4 °C of the hand-derived 14.4** from
the original 60-run matrix (the tool independently reproducing the
ground-truth calibration). Result panel + Apply button
browser-verified: the click wrote `cool_flow_rise = 14.8` to the
conf (cleared after; the compiled default stands until the operator
chooses otherwise).

### Units / identity / position panel rework

**Units/identity/position panel rework (2026-08-08, later):
OFFLINE-VERIFIED ONLY — board deploy + bump HELD during the
operator's firmware-upgrade bench testing.** Verified against the
`tools/mock.py` harness in forgectrl (serves the ui.c panel with
mock endpoints; POSTs logged): fuse-identity header (sample id), red
unreferenced position (needed the `.kv>span:first-child` selector
fix — the old descendant selector out-specified `.b-bad` on nested
value spans), imperial placeholders 14.4→25.9 (delta) / 33→91.4
(absolute), position 12.34 mm→0.486 in, dirty-save posting exactly
one changed key converted back (27 °F→15 °C), diag bands ×1.8 with
Apply still posting metric, and a units round-trip leaving nothing
dirty. The C serial→hostname derivation matches gfhardware id.py on
200k random 32-bit serials (host-side cross-check). Also
offline-verified the same way: the **fuse-identity viewer** (GF
Cloud tab, `GET /fuse-identity` fetched on demand only — serial,
derived hostname, and the 64-hex SRK password with a
keep-these-secret warning; modal outside the settings lock, both
dismiss paths clear the values from the DOM).
**LIVE-VERIFIED 2026-08-08 after the firmware-testing hold lifted**
(both binaries hot-deployed onto the fresh 20260808171449 image,
which already shipped the driver at the bumped pin): header reads
the machine's **real fuse identity** — the C derivation confirmed
against its known factory hostname — with
`gf_hostname`/`hostname` gone from /settings; position shows
0,0,0 in red on the unhomed fresh boot and re-renders in inches on
the live units toggle (placeholder 25.9, clean metric round-trip,
conf key cleared after); /fuse-identity returns the real 8-digit
serial + the derived hostname + a 64-hex password (verified by shape, not
echoed), modal opens and clears on close; driver smoke: one M8
flow check verified 10.5/9.5 on the redeployed binary. forgectrl
pin bumped to the panel rework revision.

### Wireless regulatory + region setting

**Wireless regulatory + region setting (2026-08-08, later):** the
boot-time `cfg80211: failed to load regulatory.db` never was a
missing file — packagegroup-base-wifi has always shipped
regulatory.db(.p7s) + iw on both images. The cause:
imx_v6_v7_defconfig builds cfg80211 IN (=y), so it requests the db at
~2.51 s, before `VFS: Mounted root` at ~2.62 s; the load fails (-2)
and stays failed — a later `iw reg set` alone does NOT retry the
file, only an explicit `iw reg reload` recovers it. Fixes shipped:
glowforge.cfg flips CFG80211/MAC80211 to =m (they load with wlcore at
~5.5 s, well after mount, so the direct load succeeds — kills the
message; in the kernel batch above, awaiting the next SD burn), and
forgectrl gained `wifi_country` (System-tab Wireless card, full ISO
3166-1 alpha-2 dropdown, default 00 = world) applied via
`iw reg reload` + `iw reg set <cc>` at daemon startup and on every
change. LIVE-VERIFIED on the flashed 20260808171449 image
(hot-deployed forgectrl): startup domain is the db-backed world
regdom (it shows the 755–928 MHz S1G rules only the db carries),
`POST /settings?wifi_country=US` flipped the kernel to
`country US: DFS-FCC`, and clearing the key returned 00 and removed
it from the conf. The release image still builds under the 200 MiB
slot cap; an explicit wireless-regdb-static image entry was reverted
as redundant (packagegroup-base-wifi covers it).
Power save: the flashed kernel default is on
(CFG80211_DEFAULT_PS=y), so the same forgectrl startup pass pins
`wlan0 power_save off` (cold-boot verified off on the flashed
image); the kernel batch flips the default off too. Quirk: hinting
`iw reg set 00` while the kernel is already in its default world
domain makes cfg80211 intersect world-with-world and report the
alias `country 98` (identical rules, confusing label) — the startup
pass therefore hints a region only when one is set, and hints 00
only to revert a live region change. Consequence, reboot-verified:
with the db loaded and no user hint, cfg80211 follows the AP's
802.11d country IE (the bench AP advertises US — fresh boot came up
`country US: DFS-FCC` with the setting unset; no `country=` in the
supplicant conf, wl18xx does not self-hint), a user-set region
overrides the IE (DE applied while associated to the US AP), and
clearing reverts to the 00 hint. The UI labels the default
accordingly ("Automatic — AP country, else World").

### Flow-fault triage resolved

- **TRIAGE RESOLVED 2026-08-08 — the 2026-08-03 faults were a
  REAL transient stagnation, not false positives; loop trusted
  again.** The log lines (pass rise 11.4, then FAULT 16.5 / 15.9,
  dT 11.6) postdate the warm-baseline validation session:
  `flow_warm_validate.py`'s controller restart truncates
  `/data/glowforge.log` (single `>`), so they were written by a
  driver M8 session after 23:21 on 2026-08-02 — right after a
  bench session that stopped/started the pump 8+ times with
  ~50 °C heater excursions (classic airlock conditions).
  Signature analysis against the design matrix: the fault rises
  sit at the characterized no-flow floor (16.04), and the
  establish-window dT 11.6 sits in the no-flow band (driver-
  equivalent dT-mean from the matrix: no-flow 11.9–13.2 vs flow
  9.8–10.2) — the checks correctly read stagnant/near-stagnant
  water at that moment. Probable cause: transient pump airlock
  from the bench session's pump cycling, self-cleared (the
  preceding 11.4 pass shows flow was fine minutes earlier).
  **Re-verified 2026-08-08 through the production path** (M8 on
  the flashed v0.1.0 image, pump operator-confirmed, 22 °C
  settled loop): rise 11.3 dT 9.5, and after an M9→M8
  layer-cycle, rise 10.8 dT 9.3 — textbook flow-band values.
  Also measured: **no recirculating heat slug** — each check's
  heat is fully shed within ~60 s (two checks left the loop
  0.4 °C net cooler), and fan-profile transitions inject brief
  ~1.7 °C COLD slugs from the radiator (~20 s), showing the loop
  circulates in tens of seconds. Operational lesson: expect a
  possible legitimate flow SUSPECT on the first checks after
  manual pump stop/start cycling — the confirmation machinery
  below absorbs it.

### Suspicion / confirmation state machine

- **Suspicion/confirmation state machine — IMPLEMENTED
  2026-08-08, bench-drilled 6/6 + escalation** (now in the
  forgectrl engine). An over-limit check is a SUSPICION,
  not a fault: `COOLANT FLOW SUSPECT` warning + an immediate
  re-check request (no cadence wait). The next completed check
  decides it — "consecutive" means no clean check in between,
  whatever the wall-clock gap: over-limit again →
  `COOLANT FLOW FAULT`; clean → `coolant flow suspicion
  cleared`, episode counted (3 cleared episodes in one job earn
  an aggregated check-your-coolant warning; counter resets when
  cooldown reaches idle). A suspicion that cannot produce any
  verdict within `GFCOOL_CONFIRM_MAX_S` (default 480 s; budget
  restarts per flood session, runs only in Cool_Run) escalates
  to FAULT — a loop that will not settle after a fault-level
  reading has shown no evidence of health. A clean check from
  the FAULT state logs `coolant flow recovered`. Laser
  milestone: safe posture (hold + laser off + forced cooling)
  moves to the SUSPECT edge; FAULT stays the hard fire gate.
  Every threshold in this machinery is a `cool_*` conf key since
  2026-08-08 (forgectrl Machine tab, re-read per flood start;
  verification/calibration tools in the Diagnostics section).
  Bench drill (`scripts/bench/flow_confirm_drill.py`, on-board,
  real pump-off transients through the production path, single
  M8 session): verified 11.6/9.4 → pump off SUSPECT 16.4/12.0 →
  pump on cleared 11.9/9.5 in 92 s (the 2026-08-03 field case,
  now non-fatal) → pump off SUSPECT 18.5 → still-off confirmed
  FAULT 16.1 just 109 s after the suspect → pump on recovered
  11.1/9.4. All six verdicts in order, 6/6. Escalation drilled
  separately (`flow_escalate_drill.py` with
  GFCOOL_CONFIRM_MAX_S=45): suspect → starved settle → "no
  clean re-check within 45 s" FAULT.

### Install / update system — Phases 0, 1 and 2

**Install/update system overhaul** (planned 2026-08-08): adopt the
factory A/B slot scheme end-to-end — fwup-packaged signed `.fw`
releases, single-stage installer, GUI update manager + boot
selector in forgectrl, offline factory restore from a `/data`
archive, legacy-p4 migration, and later a refreshed recovery image
in boot0. Full phased plan with invariants and decision gates:
`docs/UPDATE-SYSTEM.md` (builds on the facts-bank eMMC map).
**Phase 0 COMPLETE, hardware-verified 2026-08-08**: slot-agnostic
images (`root=${mmcroot}`; the SAME release ext4 boot-verified from
SD and from eMMC p4, steered by env alone — bench flip test), fwup
toolchain cross-version proven (modern-packed signed `.fw` applies
with the factory's 0.14.2; 0.14.2 wants raw 32-byte pubkeys), fwup
in both images, slot-sized release rootfs + hard size gate + ext4
artifact + `scripts/mkfw.sh`. GAP found for Phase 1: the image
ships fw_env tooling but **no `/etc/fw_env.config`** — hand-placed
on the bench SD system (factory-identical: mmcblk2 0x80000/0x82000,
0x2000, redundant) — the ffboot-v2 recipe must install it.
**Phase 1 COMPLETE, hardware-verified 2026-08-08**: ffboot v2 —
`-l` machine-parsable slot inventory (the shared probe for the
installer and the forgectrl update manager), verified atomic
four-variable env flips (one `fw_setenv -s` transaction, read-back
verify, libubootenv→classic→per-var format fallbacks — works on
both fw_setenv flavors), content-probe gate on switch targets
(`-f` overrides), probe-based `-e` newest-factory selection. The
`ffboot` recipe installs `/usr/sbin/ffboot` + `/etc/fw_env.config`
in the image (closes the gap above; build 20260808160821, ext4
still 180.8 MiB). Bench: `-l` classified every slot correctly, and
ffboot itself drove the SD→p4→SD flip cycle (probe gate, both
flips, clean returns). Untested edge: empty/unreadable-slot
classification (no such slot on the bench; exercised naturally
when Phase 2 overwrites a slot mid-install).
**Phase 2 COMPLETE — FULL SLOT INSTALL bench-proven end-to-end
2026-08-08** (operator at the factory console, agent over SSH):
single-stage installer ran on the FACTORY 2024 firmware — archived
both factory rootfs versions + boot0/boot1 (~88 MB total, manifest
with md5s), signature-verified the dev-signed forgefirm.fw, applied
it to slot 2 with the factory's own fwup (29 s), post-verified,
verified-flipped, and ForgeFIRM booted from slot 2; slotmigrate
reclaimed p4 and grew /data to the **byte-exact factory geometry**
(827392/6725632; 0.7 s at boot, silent no-op thereafter); factory
round-trip proven (`ffboot -e` → factory 2024 boots → `-e2` back).
2024-firmware facts learned: no `/factory/imgN` mounts, generic
fw_env.config points at the WRONG device (use per-device
`fw_env_mmcblk2.config` — ffboot's selection logic), no SSH (serial
console only), factory kernel cannot see the SD card (ffboot -s
needs `-f` from factory). The **bench board now runs ForgeFIRM
v0.1.0 from eMMC slot 2** (factory 2024 in slot 1, archives in
/data/forgefirm/archive, dev image still on SD via `ffboot -s`).
The installer's embedded pubkey is the **production release key**
(ceremony executed 2026-08-08; `release.sh` enforces the match).
**Post-test: the bench rests on the SD dev image again** (`ffboot
-s`; slot 1 = factory 2024, slot 2 = ForgeFIRM v0.1.0, archives in
/data/forgefirm/archive). Platform fact pinned by experiment while
chasing a console cosmetic: **busybox mount's auto-type iteration
against an already-mounted ext4 device prints a kernel
"`Can't open blockdev`" for each foreign-type (ext3/ext2) exclusive
claim before the ext4 attempt joins the existing superblock** — the
image's fstab keeps the factory slots mounted under /factory, so
any auto-type probe of a slot triggered it. Cosmetic only; ffboot
and the installer now reuse existing mountpoints from /proc/mounts
and mount fresh targets with explicit `-t ext4` (verified: dmesg
count unchanged across `ffboot -l`).

### SD images 20260808011035

Previously — **SD images 20260808011035 built**
(forgefirm-image + -dev): the first images carrying the whole
control-panel era — gfcloud homing, the OpenGlow-branded panel with
the /status dashboard, controller-mode selector + boot dispatch, the
idle settings lock, and all four platform bug fixes (estop gate,
cnc.halt, forgectrl-routed captures, blocking dms chain). Also: the
control panel carries the
**OpenGlow visual identity** (navy header + recreated starburst
wordmark, light content, laser red as accent only) and the status
page is an **operational dashboard**: motion state + true machine
position (kernel step counters anchored at homing via
`/run/grblhal.homed` — the Grbl socket is never polled, a connection
there displaces the sender), coolant temps, pump/TEC, all four fan
tachs (air assist µs @ 8 ppr, chassis fans ns @ 2 ppr — live-checked),
laser lockout (interlock_circuit b3; `cnc/laser_latch` is
write-only), and the safety switches via EVIOCGSW (head sense reads
not-detected with a working head — display it dim, not alarming).
Previous same-day work: control panel + calibration + identity
overrides + multi-key `/settings`; **gfcloud homing LIVE-VERIFIED
end-to-end** ($H → homed at the factory corner in 65 s; four platform
bugs fixed — see Next work #3); fd-blocking protocol pacing; the
fortify step_us_min fix.

## 2026-08-11 … 2026-08-13 — first light, the wedge, shared services

### First light and the no-motion root cause

- **2026-08-11: the failed first-light attempts' no-motion root
  cause — fast 40 V motor-rail bounces — found and mitigated.**
  An off→on bounce of the 40 V rail within ~tens to hundreds of
  ms (the gfhome→grbl homing handover measured 38–360 ms in
  dmesg) can leave the supply folded back: SDMA playback and the
  position/byte counters run in exact real time while the X/Y
  motors produce no torque, or stall mid-sweep. Bench matrix:
  raw replay of the captured job stream (bytes verified to carry
  correct steps/fire/power content) reproduced no-motion with
  perfect counters; `disable` → ≥2 s rail-off → `clear_all
  (lseek 0)` → `enable` restores torque; a deliberate 40 ms
  bounce reproduced a mid-sweep stall; one post-heal baseline
  still failed — **the rail is marginal at the hardware level;
  watch it**. Exonerated by bisection (Z-hall stream probes +
  operator-observed 20 mm X sweeps): stream content, kernel
  module and SDMA context, the granular lseek clears, analog
  config values, PIC currents, close/reopen, stop, halt.
  Driver mitigation (grblHAL-glowforge b7264bf): every takeover
  of the pulse device (init and homing-session resume) starts
  with a deliberate rail-off settle, conf key `rail_settle_s`
  (default 2.5 s, 0 disables).
  **SAFETY COROLLARY: advancing position counters are NOT proof
  of physical motion** — an armed job can fire with the gantry
  stalled (dwell burn). The laser milestone needs a physical
  motion-liveness gate (limit switches when they land, or the
  head accelerometer); until then the first-light procedure is:
  operator watches from the first commanded move and stops the
  job on any no-motion.
- **2026-08-11 (later, same day): root cause corrected and the
  liveness gate landed.** The supply is fine — the **DRV8825
  stepper drivers wedge on rail glitches** (operator diagnosis;
  see the hardware facts bank in `BRINGUP.md`): whether a given power-up leaves
  them unserviceable is chance, which is why one clean-settle
  baseline still failed. The mitigation stack is now: the
  pulse-device broker (the rail never cycles on handovers), the
  supervisor's **head-accelerometer liveness probe** before each
  session's first controller spawn (+X-first per the cable rule,
  laser latched; rail-off recovery ladder 5/15/30 s on a dead
  verdict; `motion-fault` state when the drivers won't recover),
  and **gfhome's hardened completion** (a run of near-identical
  cloud corrections aborts the session; quiet without an
  accel-witnessed motion window is a failure, not a homing —
  proven the hard way when the service repeated one correction
  eleven times into a motionless gantry, gave up, and the old
  quiet heuristic reported homed). A genuine accel-witnessed
  homing (8 motion windows, head at the corner,
  operator-confirmed) closed the episode.

### GRBL-mode laser software: implementation record

- **GRBL-MODE LASER SOFTWARE: IMPLEMENTED 2026-08-09, bench-verified
  without fire. FIRST LIGHT LANDED 2026-08-11 — first GRBL-mode burn
  completed (operator-run LightBurn job, chain armed, motor-rail
  settle in place).**
  - Architecture: the real spindle lives in
    `grblHAL-glowforge/src/glowforge_laser.c`; per-segment spindle
    updates (the core's laser-mode path, running on the stepper
    producer thread at exact virtual-tick positions) map power/fire
    transitions onto the pulse-byte grid via `gf_stream_laser()`,
    and the shipper emits them: a power byte (0x80 | 7-bit duty,
    raw PWMSAR counts, 127 = 100 %) inserted ahead of the first
    tick byte it covers, FIRE as bit 4 OR'd into tick bytes. The
    spindle PWM is precomputed to a period of exactly 127 so
    computed values ARE power bytes ($30 default 1000 → S1000 =
    127). Contract rules enforced structurally: a power byte leads
    every kernel run before any fire bit (run start resets duty to
    ~100 %), transitions are coalesced per tick so power bytes are
    never consecutive, and power bytes cost no machine tick (the
    SDMA script processes the following byte in the same EPIT
    interrupt), leaving the wall-clock due math untouched. Fire
    only ever rides motion segments of laser blocks - jogs, G0 and
    homing are fire-free by construction, and the end-of-data
    backstop covers every stream end.
  - **Arming - the operator's button press is required.** The first
    laser-on of a job (M3/M4, always planner-synced by the core)
    refuses outright if a coolant fire gate stands, else forces the
    run fan profile on, unlocks the kernel laser latch, lights the
    button white and blocks the gcode stream - pumping real-time
    traffic exactly like the homing session - until the operator
    presses the physical button (EV_SW bit 2), a soft reset aborts,
    or `laser_button_timeout_s` (default 300 s) expires into
    alarm 3. The armed window survives S changes and M5/M3 toggles
    (no re-prompt mid-job) and closes - relocking the latch - after
    `laser_disarm_s` (default 60 s) of spindle-off idle, or
    immediately on alarm/homing/reset/stream fault. Both keys live
    in the shared machine config, re-read per arm.
  - **Underrun policy while armed: fail safe, no retry.** The
    stop/run recovery restarts the kernel run, which resets the
    duty to ~100 % - replaying queued fire bits would fire at full
    power - so an armed underrun acks the kernel and faults (alarm,
    latch relock). Motion-only streams keep the one-shot retry.
  - **Coolant fire gates live** (`gfcool_fire_ok`): flow FAULT or
    over-ceiling coolant temperature (resume-gate hysteresis)
    blocks arming and suppresses fire mid-job with a loud warning.
    While armed the run fan profile + flow interrogation are forced
    on regardless of the sender's M8/M9; a flow SUSPECT/FAULT
    verdict inside an armed window takes the safe posture (feed
    hold + run airflow; laser mode drops the spindle in hold).
    SUSPECT auto-resumes on a clean re-check; FAULT leaves the hold
    and the gate for the operator.
  - **Host verification** (`scripts/bench/laser_stream_test.py`,
    null-sink + `GFSINK_DUMP` stream capture, M4 job S500→S1000
    with a G0 return): power byte leads the stream, no consecutive
    power bytes, first FIRE bit rides nonzero duty, M4 dynamic
    accel scaling visible (duties 44/52 on the ramp), S500 plateau
    63 / S1000 127 exact, 28 354 fire ticks = the cutting time at
    28160 Hz, X peak 533 steps net 0 (steps survive the
    insertions), and 534 dark steps after the last fire bit = the
    entire G0 return.
  - **On-board no-fire verification 15/15 PASS** (chain unarmed,
    nobody at the button; the drill script was a bench one-off and
    is not retained — the arm-window state machine is reproduced
    host-side by `scripts/bench/laser_lifecycle_test.py` and grblHAL's
    `tests/laser_arm_test.c`, and the latch readbacks on hardware by
    `gate_a_kernel_drills.py` and `live_fire_drills.py`): latch locked
    at idle and through jogs (interlock_circuit 13), M4 → prompt +
    latch unlocked (5) + button LED white + run fans forced +
    status served during the wait, soft-reset abort relocks + LED
    off, 3 s timeout drill → warning + ALARM:3 + relock, jogs
    clean after. One transient on the first-ever arm: the
    air-assist run write didn't land (204) - a head-I²C first-write
    blip; deterministic PASS on every rerun, and real jobs re-apply
    run fans with every M8. Note for senders: a disconnecting
    sender leaves a pending arm wait until the button timeout
    clears it (latch relocks then).

### Interlock readback semantics cross-check

- **Interlock readback semantics cross-check: CLOSED 2026-08-12.**
  The full `interlock_circuit` bitmask is mapped: b0 (SoC-side
  LASER_ON monitor, active low), b1 (FIRE, active high) and b3
  (latch, 1 = locked) were pinned by the 2026-08-02 scope
  experiment recorded in the gate section above; b2 (button latch)
  and b4 (interlock latch reset) come from the factory decode the
  attrs were ported from. The armed kill-mid-FIRE drills exercised
  the mask across armed, firing, idle and disarmed states with
  consistent readings, and interlock-trip recovery is confirmed
  from commissioning runs. Attribute semantics are documented in
  `kernel-module-glowforge/UAPI.md`; note `cnc/laser_latch` is
  write-only, so lock state is read from `interlock_circuit` b3.

### Shared machine services complete and closed out

Previously — **shared machine services complete and
closed out (2026-08-13).** forgectrl is the one machine-services daemon behind both
controller modes: the cooling engine (single owner of the thermal
hardware), controller-mode supervision, the pulse-device broker, and
the motion-liveness gate. Both controllers are cooling-engine clients
that enforce the published verdict in-process, and cloud mode ran an
**11.4 h signed-in soak** on that final stack (12 auth-token refreshes,
clean stop from the panel and from SIGTERM). First light landed
2026-08-11 (GRBL mode, operator-run) and the armed kill-mid-FIRE drill
passed 2026-08-12. The contract is `forgectrl/docs/SERVICES.md`;
what is left of that work is item 8 under Next work.

### Shared machine services — the drills

**Shared machine services: complete, bench-verified, and closed out
(2026-08-11 … 2026-08-13).**
forgectrl is the machine-services daemon: the cooling engine (single
thermal-hardware owner for both controller modes, flow verification and
over-temp policy behind the `/cool/state` + verdict-file channels), the
controller-mode supervisor (one managed child, live `POST /mode`
switching, crash respawn with machine safing, a respawn wrapper on
forgectrl itself with retake-at-idle), the pulse-device broker (one
exclusive `/dev/glowforge` hold for the daemon's lifetime — handovers
and respawns never cycle the 40 V rail), and the **motion-liveness
gate**: the head accelerometer is the only truth about physical motion
(the DRV8825 drivers can wedge unserviceably on rail glitches with
counters running normally — see the hardware facts bank in `BRINGUP.md`), so the
supervisor probes real motion before each session's first controller
spawn and gfhome refuses to report a homing the accelerometer did not
witness. The contract for all of it is `forgectrl/docs/SERVICES.md`.
Both controllers are clients of the engine: the GRBL driver's
`glowforge_cooling.c` and the cloud client's `coolsvc.py` report job
state at 1 Hz and enforce the verdict file on their own fire paths,
each with a compiled-in run-duty fallback for the case where the engine
is provably absent. Drilled on the board with the operator present:
engine loss mid-flood and mid-flow-check (warning, fans held, heater
dropped, restore and resume), an armed kill-mid-FIRE (FIRE gone within
15–171 ms, latch relocked, burn line ends abruptly), over-temp hold and
auto-resume inside a real cycle, live mode switches, and a **11.4 h
cloud-mode soak** on the finished stack. Remaining polish: Next work
item 8.

## 2026-08-13 … 2026-08-15 — audit remediation (159 findings, Phases 0-11)

An independent whole-tree audit dated 2026-08-13 produced 159 findings. The
remediation ran as twelve phases, sequenced behind two gates — **GATE A**
(uncommanded energy) before any further live fire, **GATE B** (control surface
and release) before any published release. Both are bench-closed; the drills
are in the bench-campaign section that follows. The audit's own working files
(the findings list, the remediation plan) were retired when the last phase
landed.

### The images that carried it

Image `20260814223300` (forgefirm-image + forgefirm-image-dev)
carries every kernel/image row through Phase 9 and is flashed on the
bench; built-image checks pass: the release rootfs has root locked (`*`
in `/etc/shadow`), no watchdog daemon, forgefirm-logrotate installed,
and `K80grblhal`/`K80gfcloud` ahead of `K90forgectrl` at runlevel 6;
the kernel config carries `CONFIG_IMX2_WDT`, `CONFIG_PANIC_ON_OOPS`,
and `CONFIG_PREEMPT`; the DTB fallback bootargs is console-only;
`glowforge.ko` (the full hardening batch) is in `/lib/modules`. The
Phase 11 sweep (below) is host-verified, pinned, and its controller and
daemon halves are installed on the bench; its kernel half is doc/SPDX-only.
**Image `20260815105250` (forgefirm-image + forgefirm-image-dev) is built
on the Phase 11 pins** — the first image whose license manifest declares
`python3-gfhardware` as `MIT & LGPL-2.1-or-later` and `wlconf` as
`GPL-2.0-only` (packaged output) — with the same built-image checks passing
(root locked, no watchdog daemon, K80/K90 order, `glowforge.ko` and both
controller binaries present) and the buildpaths QA warning gone (the shipped
grblHAL `--version` flags string carries no host paths). Its only build
warning is a stamp-taint note from an earlier forced `do_compile`. **Flashed
on the bench by the operator 2026-08-15** — the board now runs the pinned
Phase 11 userspace from the image rather than hot-installed binaries. With
that, the audit's working files (the findings list, the remediation plan)
are retired: every finding is fixed, every deliberate leftover lives in
"Next work" in `BRINGUP.md`, and the runbook is the record.

### Phase 0 and Phase 1 (GATE A, uncommanded energy)

Phase 0: user-facing laser-safety and
regulatory text is in place (LIGHTBURN.md "Before you cut", README,
INSTALL.md "Regulatory and legal" + updater-first update path, a
persistent panel safety banner), the walkthrough no longer claims the
laser cannot fire, bench-machine identity and the signing-key location
are scrubbed from tracked files (bench scripts take `GF_HOST`), and
every repo has a commit-msg hook enforcing commit attribution. Phase 1
(GATE A, uncommanded energy) is **code-complete and host-verified**:
the stream engine records the cycle-end laser-off so idle-gap pads ship
dark and every stream terminates FIRE-clear (G-1), latch writes are
serialized against the shipper's relight (G-5) with the arm-state and
verdict caches made properly atomic (G-19/G-20/G-21), the cooling
report path moved to a bounded-connect reporter thread off the protocol
thread (A-3/G-7), and gf.lock is priority-inheriting with PIC-SPI and
rail-settle work moved outside it (G-8). Kernel fixes K-1 (saturating
decel ramp + EPIT divisor clamp), K-2 (resume-waypoint latch guard) and
K-3 (latch writes under status_lock; FIRE drive never restored mid-run
or mid-ramp) are code-complete and **ride the pending full-image
flash** with the platform-hygiene batch. `scripts/bench/
laser_stream_test.py` now asserts the termination and zero-step-gap
rules across M4, M3-to-stream-end, and cycle-churn sessions (with a
hermetic cooling-verdict publisher): all PASS on the fixed controller
(the M4 session reproduces the recorded baseline byte-for-byte:
28 354 fire ticks, X peak 533 net 0, 534 dark return steps), and a
build with only the G-1 hunks reverted FAILS on the M3 termination
rule — the harness catches the defect class. **GATE A stays open — no
live-fire — until the flashed image passes the bench drills**
(controlled stop decelerates at the default cloud tick, resume with the
latch locked stays laser-less, mid-ramp latch writes do not re-arm
FIRE) and the harness is wired into CI.

### Phase 2 (GATE B, control surface + release)

**Phase 2 (GATE B, control surface + release) is code-complete and
host-verified.** forgectrl now has one auth layer applied to every
endpoint (`src/auth.c`): a first-boot bearer token in `/data`, embedded
in the panel and required on every state-changing call; a Host
address-literal check plus `Sec-Fetch-Site`/`Origin` validation that
refuses cross-site (CSRF) and DNS-rebinding requests; `/cool/state`
restricted to a loopback peer so a LAN client can no longer spoof a
thermal stand-down (F-1, F-2). The irrevocable fuse view and
unsigned-firmware installs additionally require the physical button held
(F-19, F-1). A native unit test of the real `auth.c` decision logic
passes all ten cases (authorized POST allowed; CSRF refused even with a
token; rebinding host refused; missing/wrong token refused; panel
bootstrap refused over a rebinding host; loopback report allowed, LAN
spoof refused). Also fixed: the `reply_settings` accumulator overflow
and its unbounded validators (F-4, F-18); cooling-tunable caps + a
resume-below-max cross-check + a loud flow-checks-disabled indicator
(F-5); the upload path is auth+idle+job gated (F-9); the liveness probe
refuses to move the gantry with a lid/interlock open (F-13);
`update_job_running()` cross-checks added to the diag and mode-switch
gates (F-14, partial — targeted checks, not yet a single-lock arbiter);
`machine_is_idle()` fails **closed** on a read error so a connection
flood can no longer read as idle mid-cut (X-2); the fd ceiling is raised
(F-15, partial — the MHD connection cap and moving the camera
`ensure_engine` `popen()`s out of the HTTP callback are deferred);
`esc()` and the panel attribute/innerHTML interpolations are escaped
(F-20); the restore `sh -c` double-shell is gone and the archive name is
charset-restricted (B-9). Release engineering: `debug-tweaks` moved out
of the shared kas config into `forgefirm-image-dev.bb` so the release
`forgefirm-image` is no longer passwordless-root, with a `release.sh`
gate that reads the built rootfs `/etc/shadow` and fails on an empty
root password (B-1); the installer copies `ffboot` out of the
signature-verified new rootfs instead of curl-ing it from a mutable ref
(B-2); `CONFIG_PANIC_ON_OOPS=y` + `panic=10` route a kernel oops into
the laser-safing panic handler (B-3, rides the image flash). **GATE B
requires a bench pass** (a CSRF probe from a second host rejected; a
spoofed `/cool/state` no longer drops the fans; a 13-max-length
`POST /settings` does not crash the daemon; a built release image shows
a non-empty root password), after which — combined with Phase 0's
safety/regulatory text — the first public `.fw` is allowed.

### Phase 3 (broker ownership / dead-man second pass)

**Phase 3 (broker ownership / dead-man second pass) is code-complete
and host-verified.** The "broker changed who owns safing" theme is
closed on the code side. The supervisor writes the two safing lines
(`cnc/stop`, `cnc/laser_latch=1`) on **every** transition out of a
running child — mode switch, diagnostics suspend, shutdown, not just
unexpected death — and again immediately after a SIGKILL escalation
(F-3). The cooling engine is the dead-man for **hangs**: a controller
silent past the 5 s report timeout with the armed window open — or with
`cnc/state` still reading `running` (a preloaded cloud ring can play
for minutes with no live feeder) — gets the same two writes from the
engine itself, and exhaust/intake never drop below cooldown duty while
the kernel still reports a run in progress (X-1). The broker fd is now
`O_CLOEXEC` with only the controller spawn clearing the flag, so
`curl`/`fwup`/`media-ctl` children can no longer pin the pulse device,
defeat the final-close backstop, or EBUSY-storm a respawn (F-6). The
GRBL stream shutdown relocks the latch explicitly, since under the
broker its close is not the final close (G-6); the cloud `_shutdown`
hook stops motion, locks the latch, and files a final disarmed/idle
report in **all** modes — gfcloud and gfhome share the hook (C-5).
OOM/RT hardening: `oom_score_adj` respawn wrapper −1000 / daemon −900 /
controllers −500, and the controller `mlockall`s so the SCHED_FIFO
shipper cannot take a major page fault (X-6; the MHD connection cap
remains the deferred half of F-15). Kernel rows **ride the pending
image flash**: pulse-device exclusivity is an atomic in-use bit instead
of a mutex locked in `open()` and unlocked in `release()` — cross-task
release is the *normal* case under the broker (K-4); a fresh open
starts with the flock dead-man disarmed and shared locks are rejected
(K-17); `thermal_make_safe()` de-energizes only the heat sources
(heater, TEC) — the coolant pump and exhaust/intake stay with the
cooling engine, so a dead-man trip no longer stops circulation and
airflow over a hot tube or airlocks the pump, and the heater soft-PWM
duty is zeroed so its timer holds the pin low (X-4). SERVICES.md now
records the watchdog scope — the hardware watchdog is a boot/system
watchdog, not a laser-safety watchdog; the fast beam stop is the
ring-drain chain, and the cloud-ring-depth residual is covered by the
engine's hang dead-man (X-7) — plus the full dead-man ownership map.
Host verification: forgectrl and the controller build clean
(`-Wall -Wextra`), the null-sink stream harness passes all emission
rules on the changed controller, and the cloud client byte-compiles.
**Bench drills pend the image flash**: SIGSTOP a controller
mid-(dry)-run — motion stopped and latch locked within the silence
window, airflow held at ≥ cooldown duty; kill forgectrl during an
update download — no pinned device, no EBUSY respawn storm; re-run the
armed kill drill on the *expected*-stop path; a kernel dead-man trip
leaves pump and airflow running.

### Phase 4 (stale-gate cluster)

**Phase 4 (stale-gate cluster) is code-complete and host-verified; all
of it is hot-deployable (no kernel rows).** The operator-armed window
is now **job-based**, not 60-second-idle-based: it closes at program
end (`M2`/`M30`/`%`, through the kernel-idle-guarded relock so a queue
tail is never severed), whenever the sender connection changes (the
serial layer exposes a client-session generation; the press that armed
the window belongs to the displaced session), and after the disarm
grace — which now counts down in Hold, Door, and Tool Change too, so a
job abandoned in Hold no longer sits armed for hours (X-3, G-10). The
coolant fire gate is re-checked after the button wait, immediately
before the window opens (G-4), and the wait budget is clamped to
1–3600 s — garbage or zero can no longer mean wait-forever with the
latch unlocked (G-18). Cloud mode's `_button_wait` gets the same
treatment: bounded by the shared `laser_button_timeout_s`, lid
re-checked every pass, and timeout/lid/cancel all relock the latch and
disarm (C-7). The cloud cancel-drop is fixed: a settings action
rejected mid-print no longer wipes the running action's id, so a
subsequent cancel actually stops the cut (C-1). forgectrl: a
controller stop that times out restores supervision instead of leaving
the machine permanently controller-less (F-7); settings mutations are
lock-serialized and a multi-key POST lands as one atomic replace
(F-10); graceful shutdown is busy-aware — fans hold their duty and the
verdict ages out instead of being unlinked, so `forgectrl restart` no
longer feed-holds a live cut and drops exhaust (F-12; the flow-check
heater still goes off unconditionally, as this engine's own heat
source). Host verification: forgectrl and the controller build clean,
the null-sink stream harness passes all emission rules byte-identical
to the recorded baseline, and both Python clients byte-compile.
**Bench items:** finish a job and confirm disarm at Idle within the
cycle (not at +60 s); abandon a job in Hold and confirm it disarms;
kill the pump during the button wait and confirm arming refuses;
cancel a cloud print with a settings action in flight and confirm
motion stops; `forgectrl restart` mid-(dry)-cut holds exhaust. These
are dry/no-fire drills except where GATE A already applies.

### Phase 5 (physical-evidence instrumentation)

**Phase 5 (physical-evidence instrumentation) is code-complete and
host-verified.** The machine now watches what it *does*, not just what
it commanded. The cooling engine's 1 Hz tick runs the witnesses:
`cnc/laser_on_sampled` — the sampled, gated output of the hardware
AND-gate — is the emission ground truth, and emission sensed with no
armed window in the recent past stops motion and locks the latch
(repeating while the evidence persists); laser power-good degradation
during an armed window warns once per session; `cnc/faults`
transitions are warned during a run; `pic/hv_current` (the only live
HV telemetry) is ranged per job (A-1, A-4, A-5). The GRBL controller
carries its own in-process witness: emission sensed while the armed
window is closed relocks the latch and raises an alarm (A-1 ctrl
half). The four `pic/lid_ir_*` channels are polled every tick — each
job logs baseline and peaks (the characterization dataset), and the
fire-abort gate (`cool_fire_ir_delta`: sustained rise above run-start
baseline → motion stopped, latch locked, verdict `FIRE` + hold, smoke
airflow held) **ships watch-only (delta 0) until the sensors are
characterized on the bench** (A-2). `/status` exposes the sampled
evidence, faults, HV, and lid IR; the panel's latch row is relabeled
*commanded* with sensed emission and power rows beside it. Cloud: a
failed head capture can no longer leave the measure laser lit — the
capture runs under try/finally and `_action_cleanup` extinguishes the
head emitters (C-3). Kernel (rides the pending image flash): the head
I²C read helpers return signed values with errno propagated, so a bus
glitch reads as an error instead of `beam_detect_analog=65531` /
`accel_irq=1` — the witnesses can no longer be spoofed by a failed
read (K-11). Host verification: forgectrl and the controller build
clean, stream harness all-PASS byte-identical, cloud client
byte-compiles. **Bench items:** command a fire window and confirm
`laser_on_sampled` tracks it (and confirm the idle-state PGOOD
polarity for the panel row); force a head I²C error and confirm the
witnesses report error, not a positive; baseline the lid IR channels
across real jobs and set `cool_fire_ir_delta`; confirm a failed head
capture leaves the measure laser off.

### Phase 6 (motion integrity)

**Phase 6 (motion integrity) is code-complete and host-verified.** A
mid-run underrun or stepper fault is no longer silently absorbed: the
shipper polls `cnc/state` at its own cadence while a kernel run is in
flight and raises the stream fault path — disarm, homing-anchor
invalidation, alarm — the moment it happens (G-2), and the sanctioned
one-shot underrun retry now invalidates the anchor and logs
position-untrusted instead of leaving `homed:true` standing (G-3). The
supervisor unlinks `/run/grblhal.homed` on every controller transition,
so a homed GRBL anchor cannot survive into cloud mode, which re-zeros
the counters it anchors (X-5). Kernel rows (**ride the pending image
flash**): backtrack is bounded by what is physically intact in the ring
and refused outright once the ring has been live-streamed since the
last clear (K-5); `resume` range-checks against the 28-bit waypoint
field instead of silently truncating — 268 435 457 no longer becomes a
waypoint of 1 (K-12); `pulsebuf_total_bytes` is 64-bit with a
saturating 32-bit position ABI, so a long stream cannot wrap it
mid-soak (K-5); ring mutators are mutex-serialized — concurrent
writers on the inherited fd, the clear-vs-run TOCTOU, and the
run-start scratch publish (K-13); and `STATE_FAULT` is recoverable via
`enable` once every non-ignored fault line physically reads clear, so
an edge glitch no longer bricks motion until module reload (K-6).
UAPI.md documents all the contract changes.

### Phase 7 (cloud-mode robustness)

**Phase 7 (cloud-mode robustness) is code-complete and host-verified;
all hot-deployable.** Cloud now fails toward stopped-and-safe: the
service loop survives malformed frames with safing in a `finally`, and
a dead WS client thread ends the session cleanly for the supervisor to
respawn (C-2); network exceptions no longer kill the reconnect thread —
an hourly reconnect during a DNS blip cannot take the machine offline
permanently (C-4); the in-run safety poll cannot be raised out of
(`cnc.state` degrades to FAULT, the verdict reader covers `TypeError`
and future-dated timestamps) and `_action_cleanup` stops motion, not
just the beam (C-6, C-24); an accepted action is never dropped and a
crashed one emits a terminal `:failed` (C-11, C-12); the cooling
reporter is exception-proof with a parting report (C-13); Z homing is
bounded (C-15). Input clamps: pulse-header values clamp to their
now-live min/max bounds before touching motion hardware (C-9);
`load_motion` validates the header before the first byte reaches the
ring and its failure return is handled (C-10); the −273.15 dead-sensor
sentinel no longer passes the start-temp gate (C-16); the dead
`firmware_download()` is deleted (C-19); `EMULATOR.BYPASS_HOMING` keys
on a code-set emulator marker (C-21). Hygiene: tokens no longer reach
the logs — no forced DEBUG, no sign-in dump, owner-only log files
(C-8); the homing accelerometer witness samples at ~100 Hz instead of
saturating the head I²C bus (C-14; re-verify the motion-window counts
against the characterized thresholds on the next live homing); one
hostname derivation, fuzz-verified over 200 k serials with the
short-serial trailing dash fixed (C-18); bounded TX queue + locked
`response_id` (C-20); plus C-17/C-22/C-23. **Bench items:** null-sink
starve drill (sender alarms, `homed` invalidated, armed job refuses at
the stale origin); `STATE_FAULT` glitch recovery without a module
reload; malformed-frame and DNS-blip injections against a live
session; oversize/bad-header job rejected before the ring loads.

### Phase 8 (kernel-module hardening)

**Phase 8 (kernel-module hardening) is code-complete; rides the image
flash.** Probe: `/dev/glowforge` registers last so the error unwind can
never deregister a device userspace already opened; the unwind clears
the SDMA interrupt callback (previously dangling into devm-freed driver
data across an `-EPROBE_DEFER` cycle) and releases the state dirent
(K-7). Remove: every userspace surface comes down before the hardware —
a concurrent attribute read can no longer reach `gpio_get_value` on
freed descriptors — and the dirent is `sysfs_put`, not leaked (K-8).
The fan-tach spinlock is initialized and taken in the IRQ handler (the
cooling engine's fan verdicts ride these two 64-bit timestamps, which
tear on arm32 unlocked) (K-9); tach IRQ setup cleans up after itself
and records only actually-requested IRQs, with idempotent teardown
(K-10). The LED trigger removes its attributes before the sync timer
delete and serializes the simulation step against its store handlers
(K-15). The kernel dead-man now **halts instead of disabling** — no
40 V rail drop, so a crash recovery is never left in the exact state
that wedges the DRV8825 drivers (K-18). Bounds: the safing-path
pin-change off-by-one (K-14); `ignored_faults` capped to the documented
0–7 with the probe fault state decided on the masked value (K-16);
`PIN_LASER_ON_HEAD` joins the SDMA pin set and the stop/shutdown
change sets (K-19); the run-start no-data gate refuses the run on a
failed head fetch (K-20); PIC single-register writes reject values
above the documented 10-bit range instead of wrapping (K-21).
**Bench (on the flashed image):** module load/unload clean under
`CONFIG_DEBUG_MUTEXES`; forced `-EPROBE_DEFER` unwinds without a
dangling callback; concurrent `cat` during remove does not fault; the
Phase 1/3/5/6 kernel drills all re-run green on this one image.

### Phase 9 (build, BSP, and release engineering)

**Phase 9 (build, BSP, and release engineering) is code-complete and
host-verified** (all shell changes pass bash and POSIX-sh syntax
checks; forgectrl builds clean). Shutdown order: controllers stop at
K80, before forgectrl at K90, so runlevel 0/6 never tears down the
cooling engine, fire gates, and broker under a running controller
(B-4). The grblhal/gfcloud init scripts are real emergency levers
routed through new authenticated `POST /controller/stop|start`
endpoints — stop halts the child and holds supervision suspended, not
idle-gated — with `status` verbs and path-anchored pkill fallbacks
(B-6); the forgectrl `restart` self-kill guard matches
`/proc/pid/exe` (B-5). `slotmigrate` gets the 2048-sector grow
tolerance (no more MBR rewrite every boot on disks where the grow
cannot land exactly), progress verification, and a three-attempt
`resize2fs` bound with the counter on p3 (B-7). `CONFIG_IMX2_WDT` is
pinned and the unconfigured watchdog daemon is deliberately dropped —
the hardware watchdog is a boot/system watchdog, and a userspace
petter only added the mid-job-reset failure mode (B-8). The
booted-slot write guard compares device numbers and fails closed under
any `root=` spelling (F-8); settings writes fsync before rename and
never rewrite a file they could not read in full (F-11); the /data
logs rotate size-capped at boot and hourly, and the camera stats spam
dropped ~100× (F-16). Release path: `release.sh` rejects multiple
versions and requires factory-era verification (explicit bypass only);
`mkfw.sh` refuses to pack without the post-sign self-check; the
installer verifies archive product/platform and prompts on a signed
downgrade instead of installing it silently; installer/ffboot temp
paths are `mktemp` (B-13, B-18, B-19, B-20). DTS: the bootargs
fallback is console-only (no `quiet`, no hardcoded SD root) and the
stale 128 MiB ring comment reads 16 MiB (B-11, B-12); wlconf data
files are 0644 (B-16); the U-Boot v2020.01 pin's security posture is
recorded in the recipe (B-17); the bench build scripts carry no
machine-local paths (B-14) and the SSH banner escape is fixed (B-15).
**Bench items:** runlevel 6 teardown order observed; `forgectrl
restart` actually restarts; the routed emergency stop holds the
controller down; a boot on a disk that cannot grow-to-last-sector does
not rewrite the MBR; a `PARTUUID=` cmdline still refuses a write into
the running slot.

### Phase 10 (tests & CI)

**Phase 10 (tests & CI) is code-complete; the safety rules are now
machine-enforced.** The grblHAL controller repo's CI builds the
null-sink binary (driver sources under `-Werror`; the core submodule
is upstream code and exempt) and runs three suites on every push: the
**laser stream emission harness** (the G-1 class), a new
**armed-window lifecycle harness** (`scripts/bench/
laser_lifecycle_test.py`: arm-once-per-job with M5/M3 persistence and
the M2 close, sender-change re-consent, grace countdown in Hold, and
blocking-verdict arm refusal — test-the-test proven: a build with the
job-based window reverted fails the first discriminating assertion),
and a **switch-map decode truth table** (D-13): the EV_SW mapping is
extracted into a pure header and asserted, including the inverted
remote-interlock sense whose flip would read a Pro lockout as
satisfied-while-open, and the opt-in e-stop gating. forgectrl's CI
builds with `-Werror` and the tree is warning-free (the remaining
unused-result and deliberate-truncation warnings are now explicit)
(D-30). `kernel-module-glowforge` has a CI at all (D-4): it
cross-compiles the module against linux-fslc 6.12 with the Glowforge
BSP overlay and config fragment, hardfp toolchain, `KCFLAGS=-Werror`
— the same bar the recipe holds — with symbol resolution left to the
image build (a `modules_prepare` tree has no `Module.symvers`). Every
CI sequence was validated locally before pushing — and CI immediately
earned its keep: running the harnesses as a non-root user exposed that
the controller's `mlockall(MCL_FUTURE)` under a finite
`RLIMIT_MEMLOCK` makes every later thread-stack mmap count against the
limit, killing the stream threads at startup. Root (the production
spawn) carries `CAP_IPC_LOCK` and is exempt, so the flashed image is
unaffected; the lock is now root-only (grblHAL `12977eb`). Not
host-testable (bench items, documented per phase): the kernel latch
relock-on-close and dead-man trip, and the motion-liveness gate.

### Phase 11 (licensing, legal, documentation hygiene)

**Phase 11 (licensing, legal, and documentation hygiene — the last
phase) is code-complete and host-verified, 2026-08-15.** Licensing:
`python3-gfhardware` declares the libdc1394 Bayer decoder it compiles
into `gfhardware._cam` (`MIT AND LGPL-2.1-or-later` in `setup.py`, SPDX
lines on `bayer.c`/`.h`, the LGPL text shipped, the rebuild/relink offer
stated in its README) and the BSP recipe carries `MIT & LGPL-2.1-or-later`
with checksums on both license texts and the decoder header; the `wlconf`
recipe declares the three regimes its vendored TI tarball actually
contains (`GPL-2.0-only & BSD-3-Clause & TI-TSPA`, checksums on the
GPL notice, `COPYING`, and the TSPA `LICENCE`; the packaged output is the
GPL-2.0-only `wlconf/` subtree — nothing from `hw/firmware/` is
installed; provenance recorded as TI WiLink8 R8.7 SP3 with its sha256;
the TSPA text lives in the layer's `custom-licenses`); `python-gfutilities`
anchors its checksum to the upstream repo's own `LICENSE`; the dead
`meta-openglow-bsp` layer is removed; SPDX identifiers now sit on every
grblHAL driver source, every kernel-module source and header, and the
cloud-mode app files; the kernel module credits both authors and the
third-party SDMA assembler tools. `bitbake -c populate_lic` on
`python3-gfhardware`, `wlconf`, and `python3-gfutilities` succeeds against
the bumped pins and deploys the expected license files. Controller
robustness (grblHAL `da4c8eb`, CI green host-side): the pulse write
treats `-ENOMEM`/`-EAGAIN` as bounded back-off (the UAPI's backpressure
semantics), retries `EINTR`, and completes partial writes; the verdict
parser trusts only a complete document (closing brace, 1 KiB buffer)
and defaults a missing `hold` to true; the listen socket and accepted
clients are close-on-exec so the homing runner can never keep port 23
bound; a missing or unwritable settings file falls back to a RAM-backed
NVS with a diagnostic instead of a crash-respawn loop; `-e`/`-p`
argument walks, the `serial_wait` ≥1 s busy spin, `GFSINK_RATE`/
`GFSINK_DEPTH_MS` ranges, the blocking delay's `sys.abort` test, and
`gfio_wr_attr` short-write/`EINTR`/missing-attr semantics are all fixed;
messages from the SCHED_FIFO shipper and from under the stream lock go
through a raw `write(2)` (no stdio lock convoy); the `--version` C-flags
string no longer carries toolchain path-remapping flags (the buildpaths
QA warning). Daemon robustness (forgectrl `ed2934b`, `-Werror` build +
unit test green): the controller environment is built before `fork()`
and passed to `execle()` (no `setenv` in the child of a multithreaded
parent), a SIGKILL escalation is never aimed at a pid the supervisor
thread already reaped, the settings file is created 0600 (the cloud
password lives there; the Python side matches), the verdict publisher
refuses an over-long document, and the release download carries
`curl --max-filesize`. `laser_button_timeout_s`, `laser_disarm_s`, and
`rail_settle_s` are accepted by `POST /settings` (bounded like the
controller's clamps) and have a home on the panel's GRBL tab. Docs:
`kas/README.md` #5 states the real 16 MiB ring arithmetic (~84 s at
200 kHz; the PREEMPT_RT decision stands on the bounded-queue-depth
argument), the deleted `kernel-module-glowforge.bbappend`/externalsrc
references are gone from kas, `release.sh`, and the cold-build workflow,
`BUILD.md` clones only what a builder needs, `README.md` states the
homing dependency honestly (GRBL mode jogs and cuts cloud-free; `$H` is
camera-referenced homing that needs a Glowforge session until switch
homing lands), `CLOUD.md` and `SERVICES.md` agree that the supervisor
starts controllers, `UAPI.md`'s sysfs tree lists `free`/`streaming`/
`underruns` (with `free` stated as advisory — the `-ENOMEM` write return
is the backpressure primitive) and the `position` counter wrap/saturate
behavior, `SERVICES.md` carries a monotonic-clock rule (no RTC on the
board), the `COOL_FLOW_RISE_C` derivation is documented for a third party
to re-run (`scripts/bench/README.md`; the bench tools take `GF_HOST` and
`GF_SSH`), the pre-first-light no-fire drill's citation names the retained
reproductions (its one-off script was never committed), British spellings
are corrected (the wire-protocol literal `cancelled` untouched),
`3d-models/` is a git repo, dev-machine paths and the build-distro name are
out of every tracked file, and the doc-nit bundle (dual-boot wording,
`tested_against_gf` described as it is wired, the image recipe comment,
the bench README tool list, the panel's System tab) is closed. Pins:
forgectrl `ed2934b`, grblHAL `da4c8eb`, kernel module `1862ad3`,
gfhardware `6c7534a`, gfutilities `6d309ae` — all pushed, bumped, and
`bitbake -c fetch`-verified. **Bench (operator, 2026-08-15): the new
controller and daemon binaries are installed on the board and the
settings file is confirmed 0600** — Phase 11 has no open items.

### Kernel platform hygiene batch

**Kernel platform hygiene — CODE-COMPLETE and build-verified
2026-08-13 (kernel-module `6fdc4b2`, meta-openglow `34a0e2e`), bench
validation pending.** The batch edits the kernel overlay (DTS +
config fragment), so it **ships with a full image flash, not a module
hot-swap** — flash the next image before running the checks. What
changed and what each item needs on the bench:
- **Panic handler enabled** (`INSTALL_PANIC_HANDLER 1`), reduced to
  what is legal in atomic context: `epit_stop()` plus a direct
  `io_change_pins(cnc_shutdown_pin_changes)` — FIRE parked, charge
  pump low so the hardware watchdog stops being fed, latch reset
  asserted, steppers de-energized. It no longer calls
  `_driver_stop()` (hrtimer cancel, sysfs notify).
  **Bench:** panic mid-motion with motors locked and the laser
  latched; confirm motion stops and the safety lines read safe.
- **`control_12v` node dropped** along with
  `CONFIG_REGULATOR_USERSPACE_CONSUMER`; the 12 V rail is
  `regulator-always-on` and nothing in userspace referenced the node.
  **Bench:** confirm the rail still comes up and the machine behaves
  identically.
- **`struct gpio_desc` layout hack removed.** The commanded decay
  mode is tracked per axis and seeded at probe to mixed decay (both
  pins requested `GPIOF_IN`), instead of reading a private kernel
  struct. **Bench:** set each mode per axis and read the attr back.
- **Module build hygiene:** `-Wno-error` dropped, `.DELETE_ON_ERROR`
  added, and the warnings that surfaced fixed (missing prototypes now
  static or declared in the new `ledtrig_smooth.h`; LED teardown no
  longer flushes the system work queue — the LED work runs on an
  ordered queue the driver owns and destroys). The recipe passes
  `KCFLAGS=-Werror` to hold the zero-warning state without making the
  module's own Makefile unusable against other kernels.
  **Bench:** LED brightness behavior, and a clean module unload.
- **Platform guards** (not reservations — dmaengine has no channel
  reservation for this path): the SDMA channel number is
  range-checked and its takeover logged; the EPIT clock rate is read
  back at probe, failing probe at zero and warning below the rate
  needed to quantize step frequencies within 1 %; and
  `io_verify_base_address()` checks the GPIO-number→bank math against
  each pin's controller node in the DT, warning rather than failing.
  **Bench:** read the two new probe lines in dmesg and confirm no
  bank warnings.
- **`head_make_safe` implemented:** measure laser off, UV LED off,
  lens motor de-energized (group-register clear-bits write) — legal
  now that the dead-man chain is blocking. Head fans and the white
  LED are deliberately left alone: `SERVICES.md` gives the fans to
  the cooling engine (whose stand-down keeps airflow after a job
  dies) and the white LED to the camera. **Bench:** trip the dead
  man's switch and read the head registers back.
- The uniprocessor locking assumption and the panic/dead-man safe
  states are documented in `kernel-module-glowforge/UAPI.md`; no
  bench item.
- **`hv_enable` rename + polarity flip (2026-08-15) rides the same
  flash.** The gpio-keys node for GPIO4_06 is now `hv_enable`,
  declared active-low, so EV_SW bit 4 reads as the HV_ENABLE output
  itself (inactive at idle, active through a run). forgectrl
  (`/status` key `switches.hv_enable`, panel "HV enable"), the grblHAL
  driver (`SW_BIT_HV_ENABLE`, no gating) and gfhardware
  (`InputSwitch.SW_HV_ENABLE`, no gating) all ship in the same image
  and read the new polarity; the DTS and that userspace must not be
  mixed across the flash (a mismatch only inverts the telemetry — nothing
  gates on the bit — but the dashboard would lie). **Image
  `20260815162923` (forgefirm-image + forgefirm-image-dev) is built on
  these pins** (forgectrl 801f1f3, grblHAL-glowforge b629c18,
  python3-gfhardware c3d1790, kernel module d750784, meta-openglow
  b1ba543): the built DTB carries the `hv_enable` node with
  `gpios = <&gpio4 6 GPIO_ACTIVE_LOW>` and no `estop` string, the rootfs
  forgectrl emits `"hv_enable"` and no `"estop"`, the grblHAL binary has
  no `estop_halts_motion`, `gfhardware/_common.py` carries
  `SW_HV_ENABLE`, and the standard built-image checks pass (root locked,
  no watchdog daemon, K80/K90 order, `glowforge.ko` in `extras/`); the
  only build warning is the usual forced-`do_compile` taint note.
  **Flashed and BENCH-VALIDATED 2026-08-15 (operator flashed; image
  reports `20260815162923 (dev)`, `/proc/device-tree/switches/hv_enable`
  present):** with `/status` and `cnc/charge_pump_alive` sampled together
  at ~10 Hz on the board through a 5 mm X jog (`$J=G91 X-5 F300`, no
  Grbl client attached, laser locked): `hv_enable:false` / pump 0 at
  idle; `true` / 1 in the same sample the state went `running`; still
  `true` / 1 in the first `idle` sample after the run; pump 0 ≈0.4 s
  after that idle sample with `hv_enable` false in the next sample
  (89 ms later); the head returned to `MPos 0.000`. The switch reads as
  HV_ENABLE itself, in lockstep with the watchdog readback.
- **GATE A kernel fixes added to the same flash (2026-08-14):**
  the controlled-deceleration ramp now floors at the minimum step
  frequency with a saturating decrement, and `epit_hz_to_divisor()`
  can no longer return the degenerate divisor 0 (a 0 Hz request maps
  to the slowest achievable tick); the resume waypoint re-enables
  the FIRE drive only when the laser latch is unlocked; and
  `laser_latch` writes run under `status_lock`, restoring the FIRE
  output drive only when no run or ramp is in flight.
  **Bench (GATE A stays open — no live-fire — until these pass):**
  a controlled-stop drill at the default cloud tick (10 kHz, ramp
  125000) shows a decelerating tail rather than a max-rate burst;
  feed-hold, jog-cancel and `^X` each land in a controlled stop with
  position preserved; a resume waypoint with the latch locked stays
  laser-less; `laser_latch=0` written mid-ramp does not re-arm FIRE
  (probe the PSU-connector LASER_ON line as in `fire_test.py`).
  **The GATE A part of this list is DONE (K1/K2/K3 + `fire_test`
  A/B/U pass on image `20260814223300`, campaign record above); the
  platform-hygiene items themselves are consolidated in item 10.**

## 2026-08-14 … 2026-08-15 — the bench campaign

### Post-flash health, GATE B, GATE A

**Bench campaign — opened 2026-08-14; image `20260814223300` flashed and
booted.** Post-flash health check passes on the board: it reports
`20260814223300 (dev)`; kernel `6.12.20-fslc` with `CONFIG_PREEMPT` and
the console-only `panic=10` command line; `CONFIG_IMX2_WDT` and
`CONFIG_PANIC_ON_OOPS` present in the running config; the hardened
`glowforge.ko` loaded with the 16 MiB `cnc-pulsebuf` no-map pool mapped
and SDMA channel 26 / EPIT up; forgectrl holds `/dev/glowforge` (40 V up,
dead-man active) and supervises the grbl controller with the
motion-liveness probe reading **verified**; the latch reads **locked**
and faults 0 at idle; the only `watchdogd` is the kernel kthread (no
userspace watchdog daemon). **GATE B is bench-verified on the
software/control-surface side.** From a second LAN host every
state-changing endpoint refuses an unauthenticated write
(`403 authentication required`); a spoofed non-literal `Host`, a
non-literal `Origin`, and a cross-site `Sec-Fetch-Site` are each refused
(`403 request origin refused`); `/cool/state` refuses a non-loopback peer
(`403 loopback only`); the four-POST unsigned-flash chain
(`upload → apply?confirm_unsigned=1 → boot → reboot`) and
`restore/factory` are each refused unauthenticated; `/fuse-identity` is
fully token-gated (F-1, F-2, F-19). The authenticated max-length
`POST /settings` probe passes without a crash: a 300-character value is
refused `400`, thirteen 16-character in-range values are accepted `200`,
and `/status`, the panel `/`, and `/settings` all keep serving, with the
settings restore verified byte-identical to the pre-test snapshot (F-4,
F-18). On-board build facts re-confirmed on the running image:
controllers stop at `K80` before forgectrl at `K90` (rc0/rc6, B-4); the
forgefirm logrotate config and init lever are installed (F-16); there is
no `/etc/watchdog.conf` or watchdog init (B-8); the wlconf data files are
0644 (B-16); the panel token is stored 0600 (the settings file's 0600
creation is Phase 11's F-23, host-verified there). **GATE A dry motion
drills pass
(latch locked, no emission, operator watching):** bounded relative jogs
move the gantry (operator-witnessed) and the grblHAL position counter
tracks the commanded moves exactly, returning to rest; a
jog-cancel (`0x85`) stops the jog cleanly short of target and returns to
`Idle` with position preserved; a feed-hold (`!`) parks with the feed
ramping to 0 (`Hold:1`→`Hold:0`) and a resume (`~`) completes the move
with no lost-step alarm; a `^X` abort decelerates under control into
`Alarm` with machine position retained, `$X` recovers to `Idle`, and a
subsequent jog runs — no DRV8825 wedge after the abort (the rail never
cycled). **Dry dead-man / disruption drills pass (latch locked, no
emission):** with only the broker and the controller holding
`/dev/glowforge` — no stray process pins it (F-6) — a `SIGKILL` of the
controller mid-move is reaped by the supervisor, which writes `cnc/stop`
+ `cnc/laser_latch=1`, unlinks the homing anchor, and respawns a fresh
controller in about a second with the latch never unlocking (F-3); a
`SIGSTOP` (hang) mid-move drains the ring into a kernel `pulse data
underrun; position no longer trusted`, halting motion fast with the latch
locked while the cooling engine's report-silence clock runs past its
window; and a `forgectrl restart` mid-move leaves the busy controller
running (reparented), lets the move finish uninterrupted, never unlinks
the cooling verdict, and has the new daemon stand by and retake at idle
(F-12). The liveness probe's designed skip-on-open path — the safety-chain
output is known to de-assert during motion, so an at-that-moment read can
skip the probe, proceed without a motion fault, and re-probe on the next
spawn — was exercised and behaved per `liveness.c`. **GATE A kernel drills PASS on this image (operator present, HV
unpowered, software witnesses — the bit-to-pin correspondence was
scope-pinned 2026-08-02):** run with forgectrl stopped so the pulse
device is free (`scripts/bench/gate_a_kernel_drills.py`). K1: a
controlled stop from the 10 kHz cloud tick decelerates in 0.091 s
(theoretical ramp 0.072 s) to `idle` with no max-rate burst and no
fault. K2: with the latch locked, a `stop` + `resume +200` replays a
2 s FIRE window with `laser_enable`/`laser_on` at 0 throughout and
interlock pinned at 13 — the waypoint provably completed (the position
counter advanced all 1000 masked steps; `motor_lock` masks the output
drive, not the counters). K3: `laser_latch=0` written inside the accel
ramp drives the latch pin (interlock 13→5, bit 3 clear) but the FIRE
output drive is never restored while the run is in flight —
`laser_enable` 0 for the entire 3.5 s FIRE-bit stream. `fire_test.py`
A/B/U reproduce the 2026-08-02 reference on the rebuilt kernel: A
(latch locked) pins interlock at 13 through 40,000 FIRE bits; B (latch
unlocked, chain unarmed) shows `laser_enable=1`/interlock 7 mid-window
with `laser_on`/`laser_on_sampled` 0 — the safety AND-gate holds; U
reaches a true underrun, the backstop drops FIRE, and `stop` acks it.
**GATE A IS CLOSED**: every Phase 1 row is fixed, the G-1 assertion is
green in CI, and the drills above are the bench log. Live fire is
permitted again. The masked K2 steps leave the un-anchored X counter
offset (+1000 steps); `homed:false` already enforces the re-home.

### The live defect the campaign caught

**The campaign caught a live defect (fixed same day):** the liveness
probe's enclosure guard read the combined-doors EV_SW bit with the
sense inverted (bit 3 set means *closed*, as the controller's switch
map decodes; the guard treated set as *open*), so the probe skipped on
every spawn with the lid closed — and would have moved the gantry with
it open. Verified live against `EVIOCGSW` (lid closed, bit 3 = 1,
probe reporting "door/interlock open"). Fixed in forgectrl `424f185`
and hot-deployed; on the next start the probe genuinely ran and the
supervision behaved exactly as designed: a first gray-zone read (head
accel p2p x=455, below the ≥500 moving threshold) was treated as NO
MOTION and re-probed rather than false-passed, and the second probe
returned MOTION OK (p2p x=3919, y=1636) — the DRV8825s are not wedged
after the drill session's rail cycles.

### X-2 connection-flood robustness

**X-2 connection-flood robustness exercised (dry):** a 500-connection
slow-drip flood from a second LAN host drove forgectrl from 7 to a peak
of 379 open fds, where it plateaued — MHD's own connection handling
caps concurrency far below the raised 4096 `RLIMIT_NOFILE`, so the
flood could not manufacture the EMFILE that the X-2 fix guards against.
The daemon never crashed, the kernel `cnc/state` stayed readable
throughout (two local `/status` probes timed out at the peak and
recovered within a second), and it returned to 7 fds with `/status`
`200` after the flood drained. The fail-closed branch itself
(`machine_is_idle()` returns busy on any `rd_attr` failure) is now
covered by a host unit test in forgectrl CI
(`tests/status_idle_test.c`, X-2): it points the sysfs reader at a temp
tree via a `GF_SYSFS_ROOT` seam and asserts not-idle on a missing state
file and under real fd exhaustion (`EMFILE`) — the connection-flood
trigger the runtime flood cannot reach while MHD caps connections below
the fd limit. Test-the-test verified: a fail-open revert fails it. Note for F-15/X-6: the
absence of an explicit `MHD_OPTION_CONNECTION_LIMIT` + per-IP cap is
still the deferred half; the default ceiling held here but a per-IP cap
remains the right hardening.

### Idle-CPU diagnosis and the pacing fix

**Idle-CPU diagnosis + pacing fix (2026-08-14).** The controller was
found at ~28% CPU while the machine appeared idle. Traced to grblHAL
being parked in the safety-door state (`Door:0`) — entered when the lid
was opened for inspection between drills, and held there awaiting a
cycle-start even after the lid closed. In any state other than
`STATE_IDLE`/`STATE_ALARM` the driver's `serial_wait` took the 200 µs
segment-production pace, so a parked Door (or Hold) busy-spun the
protocol thread. Not a regression in the audit work; the parked-state
pacing had always been tight. Fixed in grblHAL `b2cad8d`
(`motion_parked()`): a completed feed hold, a parked door (ajar or
closed), and sleep now take the coarse idle poll, while the motion
sub-phases (`Hold_Pending` decel, `Parking_Retracting`/`Resuming`) keep
the tight pace. Hot-deployed; pin bumped and fetch-verified.
**Bench-validated dry (`scripts/bench/pacing_test.py`):** idle 2.7%,
active move 35% (tight, segments flowing), parked `Hold:0` 2.7% (was
~28%), parked `Door:1`/`Door:0` 3.0% (was ~28%), and a mid-move
feed-hold→resume preserved position exactly (30.000 mm, no lost steps —
the feeder never starved through the decel and resume ramps). This pin
bump also rides P10's grblHAL CI/tests and the mlockall-root-only change
into the next image.

### Live-fire drills

**Live-fire drills PASS (operator armed, S400/40% vector marks on
scrap, `scripts/bench/live_fire_drills.py`):**

- **Phase 5 A-1 emission witness — PASS.** On a commanded fire window
  `cnc/laser_on_sampled` (surfaced as `/status` `laser.emission_samples`)
  goes to its full 255 count and returns to 0 at Idle, across two
  separate burns. This is the reliable live-emission witness.
- **Phase 5 A-5 HV telemetry — PASS.** `pic/hv_current` (`hv_current_raw`)
  tracks the cut: 0 at idle, 0→1023/661/482 raw during the three burns
  (the tube draws real current). The only HV witness on this PSU —
  `hv_voltage` is grounded, as the audit noted.
- **Phase 5 A-2 lid IR — characterized, gate left watch-only.** A 40 %
  vector cut lifts the four `pic/lid_ir` channels only ~+3 counts over
  the ambient baseline (37/36/40/40 → peaks ~40/39/42/43) — barely above
  the ±3-count ambient noise, i.e. a weak fire signal at this power.
  `cool_fire_ir_delta` therefore stays 0 (watch-only) until a
  representative high-power job is characterized; a real ignition flare
  is far brighter than a cut, so the eventual threshold sits well above
  both the cut delta and the noise (a floor near 15 counts is the
  working target, not yet committed). forgectrl's per-job telemetry line
  logs baseline/peak for all four channels.
- **pgood is not a usable witness on this PSU.** `cnc/laser_pgood_sampled`
  stayed 0 (forgectrl reads <128 as "not good") through every burn even
  while `hv_current` rail'd and the tube cut — so A-1's "surface
  laser_pgood loss" warning is a false alarm on this hardware and must
  be gated/suppressed here (or documented as expected); the emission and
  HV witnesses are the trustworthy ones. Recorded for the A-1 follow-up.
- **Phase 4 X-3 job-based disarm — PASS.** A job ending in `M2`
  (program end, as LightBurn sends) disarms in **0.1 s** at Idle; a job
  with no program end falls back to the ~60 s `laser_disarm_s` idle
  grace (measured 56.8 s). The window is job-based, not 60-s-idle-based.
- **Phase 4 G-10 disarm-in-Hold — PASS.** Armed, fired a +X move,
  feed-held mid-move (`Hold:1`); the disarm grace counts down while held
  and closes the window at 61.3 s (the bug left a job abandoned in Hold
  armed for hours).

### Closed by host unit test instead of a bench drill

**Closed by host unit test instead of a bench drill:** G-4 (the arm
must re-check `gfcool_fire_ok()` after the button wait — the verdict can
go bad during a wait that runs for minutes) now has a grblHAL CI test
(`tests/laser_arm_test.c`) that includes the driver source, stubs the
core, and drives the real `gflaser_arm()` with a good-then-bad verdict
sequence, asserting the arm refuses at the post-wait re-check (latch
locked, window never opened, alarm raised). Test-the-test verified:
removing the re-check fails it. This is cleaner than the bench drill,
which needed the pump killed in the instant after the press. **Still
config-dependent, left as-is:** Phase 6's "armed job refuses at the
stale origin after an underrun" (GRBL mode permits unhomed cutting), and
the core underrun behavior — `pulse data underrun; position no longer
trusted` with the homing anchor unlinked — is already logged in the dry
dead-man drills above. Live fire only with
the operator armed: eye protection, fire watch, exhaust running.

### Lid-IR ambient baseline

The lid-IR **ambient baseline** for the fire-watch characterization is
captured on this image (600 samples over 5.6 min at 2 Hz, lid closed,
machine idle, coolant ≈25 °C): `lid_ir_1..4` read 37.3 ±0.6, 36.3 ±0.6,
39.5 ±0.7, and 40.0 ±0.6 raw counts (total spread ±3 counts),
`hv_current` reads 0 throughout, and the emission witness
(`laser_on_sampled`) read 0 on all 600 samples — the idle plumbing for
the emission/fire/HV evidence is verified quiet end to end (`/status`
carries the sensed rows; `/cool/status` reports `fire_watch:"watch"`).
Dataset: `scripts/bench/lid_ir_ambient_baseline.csv`. When the fire
characterization sets `cool_fire_ir_delta`, it must land comfortably
above the worst normal-cut peak delta and never below ~15 counts, so
ambient noise can never trip the fire abort. The three pending GATE A
kernel drills are scripted and staged on the bench
(`scripts/bench/gate_a_kernel_drills.py`): K1 proves the
controlled-stop deceleration floor at the default cloud tick, K2
proves a resume waypoint honors the locked latch through a replayed
FIRE window, and K3 proves a mid-ramp latch unlock never re-arms the
FIRE drive — each with software witnesses (`laser_enable`, `laser_on`,
`laser_on_sampled`, interlock bit 3) plus the PSU-connector LASER_ON
scope point, run with forgectrl stopped so the pulse device is free.

### Bench session 2026-08-15

**Bench session 2026-08-15 (image `20260815105250`, operator present) —
two live-fire findings closed, one real defect found and fixed.**
Lid-IR characterization at cutting power: three 30 mm squares on scrap
(S1000 F300, S1000 F150, S800 F600); the engine's per-job telemetry read
run-start baseline → peak `58/59/64/63 → 62/60/66/66`, `56/56/61/62 →
60/61/66/68`, `56/55/61/63 → 61/60/65/66` — a worst normal-cut rise of
**+6 counts** on any channel, against ±3 counts of ambient noise. Ambient
that day read ~57–64 vs 37–40 on 08-14 (day-to-day drift ≈ +22 counts),
which is why the gate keys off the run-start baseline and never off an
absolute level. `cool_fire_ir_delta = 15` is the sized gate (≥ 2× the
worst cut rise, at the ~15-count floor); it is a hand-edited
`/data/forgefirm.conf` key, **set on the bench 2026-08-15** (verified
present, file 0600), and takes effect at the next run start — the fire
watch is armed from here on and the next real jobs are the false-trip
watch. **Flame
signature, measured the same day (machine idle):** a small candle burning
on the bed under the closed lid read `38–41 / 38–41 / 42–45 / 42–45`
against a lid-open level of `36 / 35 / 38 / 39` and a lid-closed-empty
control of `34–37 / 34–36 / 36–39 / 37–40` — closing the lid changes
nothing, the candle is **+3 to +6 counts on all four channels** for as
long as it burns. That is the same size as a full-power cut's rise, so a
threshold cannot separate a candle-sized flame from cutting and the
15-count gate will not react to a flame that small; what a material fire
of a size worth stopping for produces is unmeasured. **Then the decisive measurement, dry, the same
day: the lid-IR channels track the lid LED.** `lid_led` 0 → `2 2 1 2`,
8 → `2 2 3 2`, 131 (the resting level) → `54 55 61 62`, 255 → `172 171
190 188`. The sensors are, first of all, a photometer for the lid lamp;
every rise measured above (cuts +4–6, candle +3–6, the "+22 drift"
between sessions) is a small modulation on a lamp-set level. forgectrl's
camera engine drives `pic/lid_led` for every lid capture (132 during the
grab, previous level restored), and the resting level is not fixed (131
here, 8 after one reboot, cloud mode sets its own `LLvl`) — so a snapshot
mid-run can step every channel by tens of counts and a fixed-count gate
fires a phantom FIRE stop. **`cool_fire_ir_delta` was therefore set back
to 0 (watch-only) the same day**; the gate stays disabled until the fire
watch is lamp-aware (Next work item 10). **Armed kill on
the expected-stop path — first run FAILED, defect fixed, re-run PASS.**
With emission live, `POST /controller/stop` returned only after 5.30 s
and the operator saw ~17 mm / ~5 s of continued cutting before a
decelerated stop: the supervisor's SIGTERM was honored by the controller
as "exit once motion is done" (`driver.c` exited only outside
CYCLE/JOG/HOMING), so the job ran on until the 5 s SIGKILL escalation
and the exit safing (`escalating to SIGKILL`, exit status 0x9). Fixed on
both sides and bench-proven the same session: forgectrl `3edb7bd` writes
`cnc/stop` + `cnc/laser_latch=1` **before** the SIGTERM (kernel-level,
instantaneous, no-op when idle); grblHAL `5960f05` treats SIGINT/SIGTERM
during motion as `^X` (controlled decel, latch relocked, alarm) and exits
on the next pass, with the handler kept installed so the supervisor's
second SIGTERM cannot hard-kill it mid-cleanup — CI case
`sigterm-mid-job` (exit in 0.10 s; the old logic fails it). Re-run with
the new binaries installed: POST returned in 0.46 s, `grbl controller
exited (status 0x0)` with no SIGKILL, kernel `idle` and `armed:false` at
the first post-stop sample, emission gone within the counter's ~1 s
window; the operator saw ~1 s / a few mm of cut, then the stop. Also
found and fixed: `auth.c` read `X-ForgeFIRM-Token`/`Host`/`Origin`/
`Sec-Fetch-Site` case-sensitively (a title-casing client was refused);
now `u_map_get_case`. Bench tooling for the session is committed
(`scripts/bench/platform_drills.py`, `live_fire_drills.py` `ircut` /
`expstop` / `ctrlstart`, `fdscan.sh`). Session rules, now standing: one
live-laser run per turn with the operator's confirmation before the next;
only observations, never inferences, in live-fire reporting.
**Dry drills the same session, all PASS on the board:** decay/microstep
readback per axis (every value reads back, out-of-range `3` refused
`EINVAL`); dead-man trip readback (closing the flock'd fd mid-run →
`closed while locked and driver is running! Emergency stop`, `pic`/`head`/
`thermal: making safe`; heater and TEC off, measure laser, UV LED and Z
driver off, pump/exhaust/intake/air-assist **unchanged**); three
`rmmod`/`modprobe` cycles with a thread reading state/position/faults/
hall_sensor throughout (6618 reads served, 14162 refused while unloaded,
no oops/BUG/WARNING); the LED sequence (all bright / all dark / button
pulse 300 ms / restore) behaved as commanded, operator-witnessed;
the module's probe lines read `EPIT clock 66000000 Hz` and `SDMA channel
26 reserved for pulse playback (script at halfword 7680)` with no bank
warnings; forgectrl's helper children (`curl` during `/update/check`, the
snapshot path) never hold a pulse-device descriptor — only the controller
does; a `$H` gfcloud homing session completed in 56 s with 7 accelerometer
motion windows above the 500-count threshold at the ~100 Hz sampler
(anchor written, `H:1`); a kernel panic (`sysrq c`) mid-move stopped
motion instantly (operator-witnessed) and the board rebooted on `panic=10`
into a healthy state (liveness MOTION OK, controller running, latch
commanded locked). Observed once, cause not established: after the three
module reloads the first liveness probe read NO MOTION (p2p 343/241); the
ladder's rail-off/re-probe recovered it (p2p 3466/2163) — a module reload
resets the analog configuration, and the ladder exists for this.
**Head-absent negatives (head unplugged, machine powered up):** the head
driver fails probe (`head not detected`) and the whole `head/` sysfs
group is absent, so every head attribute reads as missing rather than
as a number; neither the daemon nor the controller logs anything
repetitive with the head gone; the liveness probe skips (`head
accelerometer not found`) and the controller starts. Three findings,
fixed and re-proven the same session: `/status switches.head` was EV_SW
bit 7 raw (reads `true` with the head unplugged) — now real presence
(the head group exists) and it read `false`; `/mode` said `motion:
"verified"` after a probe that could not run — now `"unverified"`
(forgectrl `73eda9a`); and **nothing gated arming on
head presence** — the GRBL controller now refuses the first laser-on
of a job when the head group is absent, before the latch unlocks and
before the button lights (grblHAL `91807a2`, "laser fire blocked: no head
detected" + `ALARM:3`, operator-witnessed: the button stayed dark).
The K-11 runtime-I²C-error case (a present head answering badly) and
the C-3 failed-head-capture case are not reachable with the head
unplugged and stay open.

### Interlock latch, charge-pump watchdog, hv_enable rename

**Interlock latch has no hardware trip path in ForgeFIRM (found
2026-08-15, bench-verified).** With the interlock connector unjumpered
at idle: EV_SW `interlock`=1 (loop open), `interlock_latch`=0 (not
tripped), `cnc/interlock_circuit`=13 (b4 INTERLOCK_RESET=0),
`interlock_latch_reset`=0. This matches the safing schematic: the
interlock latch (U23-2, CD4043B) has RESET = loop-closed and
SET = INTERLOCK_RESET (GPIO4_05) — an open loop only *releases* the
reset, and nothing in ForgeFIRM drives INTERLOCK_RESET (the driver
exposes it as a read-only readback, initialized low; the former
`interlock_reset` LED node that let userspace drive it is gone). So on
a machine with a real external lockout (Pro), an open loop does **not**
cut LASER_ON in hardware; enforcement is the GRBL safety-door hold on
switch code 5 and the cloud client's motion gate. Basic/Plus ship the
loop jumpered. **Decision + fix needed:** drive INTERLOCK_RESET high
whenever the loop is open and hold it until the loop closes, so Q2
blocks the LASER_ON gate in hardware (the CD4043B is set-dominant, so
the latch stays blocked until the SoC releases SET *and* the loop is
closed). **IMPLEMENTED 2026-08-15 (kernel-module, code-complete, bench
validation pending; kernel-module 015913b, meta-openglow 92d6e20 DTS +
897c175 pin, forgectrl a451e7c docs, all pushed and pins bumped
2026-08-15):** `src/cnc_interlock.{c,h}` — an in-kernel input
handler on the gpio-keys switch device (no DT change, GPIO stays with
gpio-keys) drives INTERLOCK_RESET high while EV_SW code 5 reads open,
from probe until the switch device attaches, and if it detaches
(unobservable = open); low only while an attached device reports the
loop closed. Pin init changed to `GPIOF_OUT_INIT_HIGH`. Proof so far:
host test `tests/interlock_test.c` (8 cases, `make -C tests check`,
new CI job `host-tests`) green; module cross-compiled clean against
the staged 6.12.20-fslc kernel with `KCFLAGS=-Werror`, MODPOST silent.
Ships with the next image flash (kernel changes are never hot-swapped);
bench re-run of this exact reading then expects `interlock_latch`=1 /
`interlock_circuit` b4=1 with the loop open, both clearing after it is
closed. **BENCH-VALIDATED 2026-08-15 on image 20260815150546:** loop
pulled → `interlock`=1, `interlock_latch_reset`=1, `interlock_latch`=1,
`interlock_circuit` 45→61 (b4 set), all within one 50 ms sample;
reinserted → all clear the same way. Side effect to know: the pull is
a grblHAL safety-door hold — the controller sits in `Door:0` after the
loop closes until a cycle start (`~`) returns it to Idle (a client
connecting then sees Door, not a dead link). Same batch: the charge-pump
watchdog readback (`cnc/charge_pump_alive`,
`interlock_circuit` b5; GPIO1_08 = inverted one-shot Q, new
`charge-pump-alive-gpio` + GPIO_8 pad in the linux-fslc DTS — kernel
module and DTB must ship together, the pin is required at probe; DTB
compile-checked with cpp+dtc against the staged kernel) — **also
bench-validated 2026-08-15:** two X jogs sampled at 50 Hz: `state`
running → `charge_pump_alive` 1 and `estop` 0 (pre-rename name and
polarity of today's `hv_enable`) in the same 20 ms sample;
after each run `charge_pump_alive` fell 0.325 s / 0.326 s after `idle`,
which with the 200 ms feed phase (last pulse 0.136 s / 0.118 s before
the run end) is a one-shot period of **0.46 s / 0.44 s** — matching
the measured R·C (≈500 kΩ × ≈900 nF = 0.45 s); `estop` re-asserted
with the drop both times, i.e. HV_ENABLE = DOORS_OK · WDOG_ALIVE
observed live. Full write-up of the chain: `docs/SAFETY.md`
(+ `docs/img/safety-chain.svg`).

### LightBurn door-open handling

**LightBurn door-open handling — CLOSED by item 16.** The lid no
longer parks a job in `Door` on the default policy: it cancels the job,
ends the sender's stream with a clean reset and returns the head to the
job start, so LightBurn never lives in `Door` and the Resume convention
it used to need is gone. The `Door` residency that remains under
`lid_policy = hold` is covered by `motion.lid-policy-hold` (lid parks the
job, cycle start after the lid closes finishes the move with its position
intact), bench-validated 2026-08-17.

### uSDHC pad strength brought to the factory values

**uSDHC pad strength brought to the factory values (DTS change
2026-08-15, bench validation pending — ships with the next full image
flash, per the batched kernel/BSP rule).** Trigger: one
`wl1271_sdio mmc0:0001:2: sdio write failed (-84)` (`-EILSEQ` = SDIO
bus CRC error) on the WL1805 Wi-Fi bus at 49.5 MHz SD-high-speed,
followed by wlcore's designed hardware recovery (firmware reboot +
reassociation, ~1.0 s of Wi-Fi outage) and one `ipu1_csi0: NFB4EOF`
160 ms later (a consequence of the recovery/WARN console burst, not a
co-cause). It happened at idle, 1.7 s after a kernel run ended and
~2 s after a button press — no motion, no fire, HV_ENABLE already
down — so nothing points at laser or stepper EMI. Rate observed:
1 event in 49 min of uptime. Effect if it lands mid-job: a 1–2 s
sender stall (planner drains, head pauses; laser off in M4 mode) —
a cut-quality nuisance, never a safety matter (nothing safety-relevant
crosses Wi-Fi). Finding: `glowforge.dts` drove all three uSDHC
controllers with `0x17019` (SPEED_LOW, DSE 80 Ω, 47 kΩ pull-up on
CLK too), while the factory DTB uses `0x17069`/`0x10069` (SPEED_MED,
DSE 48 Ω; no pull on CLK) for the Wi-Fi bus and `0x17059`/`0x10059`
(80 Ω) for eMMC and SD (SD2_DAT3 `0x13059`) — softer edges than the
factory at the same 50 MHz clock. `openglow_common.dtsi` now carries
the four factory-exact values (`USDHC_PAD_CTRL`, `USDHC_CLK_PAD_CTRL`,
`USDHC_SDIO_PAD_CTRL`, `USDHC_SDIO_CLK_PAD_CTRL`) and the compiled
`fsl,pins` tuples were checked byte-identical to the factory DTB's
`glowforge_usdhc1/2` and `usdhc3grp`. **Bench:** on the next image
confirm `pinconf-pins` reads `0x17069`/`0x10069` on SD1, eMMC and
Wi-Fi come up, then watch `dmesg | grep -c "sdio .* failed"` across
sessions (baseline: 1 per ~49 min). Only if it still recurs, cap
the bus with `max-frequency = <25000000>` on `&usdhc1` (halves Wi-Fi
throughput — last resort; the factory ran 50 MHz on these pads). The
`WARNING … wlcore/main.c:874 wl12xx_queue_recovery_work` block that
accompanies the event is upstream noise (an "unintended recovery"
`WARN_ON`), not a crash — the `-84` line is the signal to watch.

### Unified logging — bench validation

**Unified logging — CODE-COMPLETE, host-verified, pushed and pinned
2026-08-15; bench validation pending — ships with the next full image
flash (rsyslog replaces busybox syslogd/klogd, so it is an image
change).** Design and contract: `forgectrl/docs/SERVICES.md`
"Logging". In brief: rsyslog is the only log writer; forgectrl and
the grblHAL driver emit through the shared non-blocking `fflog`
emitter (drops, never waits — a stalled log daemon can never park a
controller thread), gfcloud/gfhome through `SysLogHandler`, the
kernel through `imklog`; a controller's stray stdout/stderr rides a
per-controller `logger` relay under its own name; the daemon's own
stray output a fifo relay in its init script. Tree:
`/data/log/forgefirm/{forgectrl,grblhal,gfcloud,gfhome,kernel,system}/`,
size-capped and rotated (`forgefirm-logging` recipe: renders the
rsyslog rules from the settings at S19 via `forgectrl
--render-syslog`, sweeps the pre-syslog files once into
`/data/forgefirm/legacy-logs/`, logrotate at boot + hourly with a
`HUP`, never `copytruncate`). Levels: `log_<logger>_disk` /
`_remote` and `syslog_server/port/proto` in `/data/forgefirm.conf`,
**applied at reboot** (the panel's Logs tab shows configured vs.
effective and offers the reboot); a process emits at the more
verbose of its two levels, rsyslog filters per destination. Export:
`POST /logs/export` streams a `tar.gz` (tree + system snapshot),
sanitized by default (`src/sanitize.c`: known values first — serial,
hostname, cloud credentials, panel token, WiFi SSID/PSK — then
patterns; stable placeholders; `tests/sanitize_test.c` in CI, 39
fixtures). Host proof done: forgectrl/grblHAL `-Werror` builds and
all three CI test sets green (sanitizer, idle fail-closed, switch
map, arm re-check, laser stream + armed-window harnesses on the
null-sink build); `tests/fflog_e2e.sh` against a private rsyslogd on
the shipped `rsyslog.conf` (emitter format, per-logger routing,
level filtering, `logger` relay routing) and the equivalent Python
check both pass; `/logs`, `/logs/tail` (full + incremental follow),
and both export variants exercised over HTTP on a host build and
the panel's Logs tab driven in a browser (levels table, viewer,
follow, export). **Bench, on the flashed image (dev image
`20260815191634`, flashed and booted by the operator 2026-08-15):**
- ~~boot~~ **DONE 2026-08-15**: `S19forgefirm-logging` → `S20syslog`
  → `S90forgectrl`, `K80`/`K90`/`K95syslog`; `rsyslogd` up, no
  busybox `syslogd`/`klogd`; rules and `/var/run/forgefirm-loglevels`
  rendered (all defaults); six directories under
  `/data/log/forgefirm`; `/var/log/messages` gone; legacy files
  moved to `/data/forgefirm/legacy-logs/` (`forgectrl.log`,
  `forgectrl.log.old`, `gfcloud.log`, `gfcloud/`, `gfhome/`),
  `/data/log/gfcloud` and `/data/log/gfhome` gone, the factory's
  `/data/glowforge.log*` untouched; the forgectrl fifo relay and the
  grblhal relay both running (`logger` ×2, `/var/run/forgectrl.stderr`).
  The swept legacy files (10.6 MB) were deleted from the bench on
  2026-08-15 once the new tree had proven itself; the sweep itself
  stays in the init script for any board upgrading from before the
  syslog tree.
- ~~routing~~ **DONE 2026-08-15** for GRBL mode: forgectrl lines
  (`super: liveness probe: MOTION OK …`, `NOTICE super: started grbl
  controller`) in `forgectrl/forgectrl.log`; grblHAL's (`gfstream:
  pulse device inherited from the broker`) in `grblhal/grblhal.log`;
  the whole boot ring (350 lines, `glowforge_cnc cnc: 40V on` …) in
  `kernel/kernel.log` with correlated timestamps; sshd/rsyslogd in
  `system/system.log`; `logger -t grblhal` / `-t gfhome` probes land
  in the right files tagged `grblhal[-]` / `gfhome[-]` (the relay
  path). `/logs`, `/logs/tail` and the sanitized export served over
  the LAN: the bundle carried `<SERIAL>` ×2, `<IP-1>` for the LAN
  peer (sshd `Accepted … from <IP-1>`), MACs and e-mails redacted,
  no LAN address anywhere in it. Still open: cloud-mode routing
  (`gfcloud/gfcloud.log` + a Python traceback via the relay) and a
  `$H` for the gfhome lines. Found and fixed the same day: rsyslogd
  warned at start that the fallback rule after the include was
  unreachable (the rendered rules end in `stop`) — the default rules
  now come from the init script when the render leaves none
  (forgefirm 7487f90, next image).
- ~~levels~~ **DONE 2026-08-15** (three reboots): `forgectrl`/`grblhal`
  → `debug`: `pending_reboot:true` before, effective after; the per-run
  `gfstream: run:` DEBUG stats appear on jogs; `forgectrl` → `warning`
  + `grblhal` → `off`: the new boot wrote zero NOTICE/INFO forgectrl
  lines and kept a WARNING probe, grblhal wrote nothing even for an
  `err` probe, kernel/system unaffected; defaults restored and
  re-verified. ~~Remote~~ **DONE 2026-08-15, real hop to a LAN
  collector (172.16.1.95:5514) over UDP and TCP** (after a first pass
  on a loopback listener): RFC 5424 lines arrive (`<31>1 …
  glowforge grblhal - - - …`), filtered exactly per logger across a
  whole boot (kernel at warning only, forgectrl/grblhal at info,
  sshd from `system`; a gfhome err and a forgectrl debug probe held
  back). Collector down through an entire boot on TCP: `omfwd
  suspended … Connection refused` in `system.log`, the machine
  unaffected (jogs, local logging), and 30 s after the listener came
  up `omfwd resumed` and the queued boot lines were delivered. Note
  for future probes: `busybox nc -u` on the board never sends — use
  `python3 … sendto`; my first "the workstation drops inbound UDP"
  reading was that false negative.
- ~~rotation~~ **DONE 2026-08-15**: a 30 000-line burst (4.8 MB) into
  `grblhal`, one `logrotate` run → `grblhal.log.1.gz` (all 30 024
  lines), the live file recreated and receiving (rsyslogd's fd on the
  new inode). The imuxsock per-pid rate limit did not engage for
  `logger` bursts (each line is a new pid) — it bounds a single
  runaway process only, as intended.
- ~~export~~ **DONE 2026-08-15**: both variants downloaded over the LAN;
  the sanitized bundle carries `<SERIAL>`, `<IP-n>`, `<MAC-n>` and no
  LAN address, the full one has them; staging empty afterwards.
- ~~RT~~ **DONE 2026-08-15**, with a finding that is NOT logging: X
  jogs (F600/F1200, ±5 mm) with `grblhal` at debug: without a camera
  stream `max behind 0–5.8 ms, clamped 0`; with the lid stream running
  steady, `max behind 6–19 ms, clamped 0–11` per run — and the same
  with rsyslogd frozen (SIGSTOP) during the runs (`clamped 0/1/0/10`),
  so the producer clamping under a live stream is the stream's CPU
  load, not the logger (no underrun, the shipper is unaffected). The
  2026-08-03 baseline said `clamped 0` at F1200 with a stream —
  re-check under item 1/10 (VPU stream + cooling engine + telemetry
  polling all landed since).
- ~~stop/start~~ **DONE 2026-08-15**: `kill -9` of the daemon → the
  wrapper's `forgectrl[-] ERR exited (137) - respawning in 5 s` lands
  through the fifo relay, the respawned daemon stood by, took over the
  unmanaged controller, re-probed motion and restarted it; a mode
  switch to cloud put gfcloud's lines (`ffmachine:_lid_image …`,
  `websocket:img_upload COMPLETE`) in `gfcloud/gfcloud.log` with a
  per-controller relay alive, and back. A `$H` (web-service homing,
  58 s, homed X0 Y0 Z10.60) put gfhome's session lines in
  `gfhome/gfhome.log` under its own pid and grblHAL's `starting
  homing session` / `homed` in `grblhal.log`. **Item closed.** Not
  separately drilled: a Python traceback through the relay — there
  is no external trigger for that; the relay pipe is the same one the
  `logger` probes and the wrapper's `exited (137)` line went through.
  Acceptance catalog: `logs.tree-tail-export` (list, tail, sanitized
  export with the token-leak check), `logs.routing` (one logger
  daemon, rendered rules and effective record consistent with
  `/logs`, the tree, the daemon's own emitter line, `logger` relay
  probes routed by name in the ff_line format, a stray program only
  in system/, kernel lines, relay processes, nothing outside the
  tree) and `logs.level-settings` (bad level/port/proto/server
  refused, a level change configured-not-effective with
  `pending_reboot`, restored) — all three PASS on the bench
  2026-08-15 through the real Runner against an isolated results log
  (the image's forgetest still carries the older catalog until the
  next dev image). Finding from that run, fixed: the sanitized export
  took 13.9 s on the target (0.95 s unsanitized) and tripped the hw
  client's 10 s default — the export call now has its own timeout
  and the sanitizer skips a pattern pass when the line cannot match
  it (4x faster on the host; forgectrl 4d19e9d). **Images
  `20260815215236` (forgefirm-image, 192.7 MB rootfs) and
  `20260815215332` (forgefirm-image-dev) are built on that pin with
  the three logs tests in the dev image's catalog** — the next flash
  carries the fast sanitizer, the init-script default rules, and the
  catalog; nothing else in the logging system is pending.

### Outstanding bench validations, as consolidated 2026-08-15

**Outstanding bench validations (consolidated 2026-08-15).** Every
safety-critical drill is done: GATE A (K1/K2/K3, `fire_test` A/B/U),
GATE B (auth/CSRF/loopback/settings-flood probes), dry motion and
dead-man drills (SIGKILL reap+safing, SIGSTOP → underrun, restart
mid-move, no stray fd), the X-2 flood, and the live-fire set (A-1
emission witness, A-5 HV telemetry, X-3 job-based disarm, G-10
grace-in-Hold, A-2 lid-IR first look). What has **not** been run on
hardware, none of it gating, in rough priority order:
- ~~**Lid-IR fire characterization at cutting power**~~ — **DONE
  2026-08-15** (three cutting-power jobs, worst rise +6 counts,
  `cool_fire_ir_delta = 15` set by hand in `/data/forgefirm.conf`).
  **Then disabled again the same day (`cool_fire_ir_delta = 0`)**:
  the channels track the lid LED (0→2, 131→~58, 255→~180 counts),
  so any lamp change during a run — a panel snapshot lights the
  lamp — steps them by tens of counts and a fixed-count gate would
  stop the job on a phantom FIRE. Redesign before re-arming: the
  engine must own or observe the lamp level (suspend the watch and
  re-baseline for a few ticks after any `lid_led` change; forgectrl
  drives it for captures, the cloud client for lid images), and the
  threshold should be relative to the lamp-set level, not a fixed
  count. Even then the signal is weak (a candle reads like a cut);
  the head camera or a real flame sensor is the honest path to fire
  detection that means something.
- ~~**Kernel platform-hygiene batch (item 9), on the flashed
  image**~~ — **DONE 2026-08-15** (panic mid-motion, decay/microstep
  readback, LED sequence + clean unload, probe lines, dead-man head
  readback, concurrent `cat` during `rmmod` — session record above).
  Still needing a debug kernel build: load/unload under
  `CONFIG_DEBUG_MUTEXES` and a forced `-EPROBE_DEFER` unwind.
- ~~**Dead-man collateral**~~ — **DONE 2026-08-15**: the trip leaves
  pump and airflow running (readback drill); helper children never
  hold the pulse device (fd-scan during `/update/check` + snapshot);
  the armed kill on the *expected*-stop path failed first (5 s of
  continued fire), the defect is fixed on both sides, and the re-run
  passed. The literal "kill forgectrl mid-download" variant needs a
  published `.fw` to download and was covered by the fd-scan instead.
- **Physical-evidence negatives:** ~~head absent at power-up~~ **DONE
  2026-08-15** (head group absent → no readings, arm refused, presence
  and motion labels fixed). Still open: a present head answering I²C
  badly (the K-11 runtime case) and a failed head capture leaving the
  measure laser off — both need the head connected and a fault
  injected.
- **Cloud mode — mostly DONE 2026-08-15:** mode switch clean (GRBL
  controller exit 0x0, gfcloud signed in, connect-time hunt + lid
  image ran); **network/DNS blip** (service peers blackholed + dead
  resolver for 75 s while the session was live): `ping/pong timed
  out - goodbye` → in-process `RECONNECTING`, sign-in retried with
  backoff through the outage, `authenticate_machine SUCCESS` and the
  service's `settings` action answered right after restore, same
  process, supervisor never involved — PASS; **a real print** (22.9 s,
  motion bytes actual = expected, emission peak 91, HV 0..932): the
  header's `AArd 1023 / EFrd 65535 / IFrd 43278` drove air 11.0 k /
  exhaust 11.8 k / intake 4.1 k rpm through the armed window and the
  hunt/Z headers (`204/0/0`) left the fans at idle levels — the
  per-job profile round-trips (directional; duty→rpm not calibrated);
  no false FIRE trip on the job. `$H` witness re-verified (7 windows
  ≥ 500 at ~100 Hz). Still open, not inducible from the bench: the
  cancel-with-a-rejected-`settings`-action case, a malformed frame
  (needs a MITM), the oversize/bad-header job (tracked in `CLOUD.md`).
- **Opportunistic:** `STATE_FAULT` recovery via `enable` without a
  module reload the next time a DRV8825 fault line actually trips.
- **Config-dependent, deliberately not gated:** an armed GRBL job
  after an underrun cuts at the stale origin unless homing is
  required (GRBL mode permits unhomed cutting; the underrun itself
  alarms and unlinks the anchor).

## 2026-08-15 … 2026-08-16 — release acceptance (forgetest)

### Campaigns on the bench

**Bench campaign opened 2026-08-15 on the flashed dev image
`20260815194415` (manifest identity `2d69a61e…`, equal to the release
build's).** The tool came up on `:8090` with all 24 tests required.
Passed that day, driven through the API with the operator present:
`image.health` (kernel options, module + 16 MiB ring, forgectrl holding
`/dev/glowforge`, K80 controllers before K90 forgectrl, 0600 token and
settings, 2.6 GiB free on /data), `kernel.latch-locked-idle` (interlock
`0x2d`, FIRE 0, LASER_ON 0/0, faults 0), `forgectrl.auth`,
`forgectrl.settings-bounds`, `forgectrl.panel-serves`,
`logs.tree-tail-export` (sanitized bundle carries no panel token),
`update.slots-and-signature` - 7 of 24. One finding, on the tool side:
`forgectrl.auth` first failed because it expected `/fuse-identity` to
answer 200 to the token alone; the endpoint is two-factor (token AND the
physical button held) by design, so the test now asserts both refusals
and never fetches the identity (a 200 would have put the fuse password
in the result log). That FAIL closed the first campaign, as the rules
say; the second campaign held the passes.

**2026-08-16, dev image `20260815215332` (26-test catalog), campaign
`c-20260816171010-cd59`: 14 of 26 satisfied** - the always-required core
`image.health`, `kernel.latch-locked-idle`, `kernel.k1-k2` (controlled
stop 0.09 s, no burst; K2 FIRE window replayed after the resume waypoint
with laser_enable/laser_on 0 throughout, counters back to start),
`kernel.k3-unlock` (mid-ramp unlock drives the latch pin, FIRE drive stays
0), `kernel.fire-abu` (A: no FIRE drive under the lock; B: FIRE driven,
LASER_ON off with the chain unarmed, FIRE clear at end-of-data; U: true
underrun, backstop drops FIRE, stop acks) and `cooling.flow-verify`
(flow 9.5 / threshold 14.4 / no-flow 16.4 C, margins 4.9/2.0, not
thin), plus `camera.snapshot` (lid snapshot half/full + a stream, operator
confirmed the bed) and the seven forgectrl/logs/update tests, which
re-passed on this image and then **inherited across two campaign
closures** - the domain-scoped inheritance and the always-required core
behaved as specified. Two campaigns closed by test-side FAILs, both
fixed: forgectrl answers a started diagnostic with 202 (the test asserted
200); and the takeover wrapper returned as soon as `forgectrl start`
succeeded, so the next test found the machine busy under the
supervisor's liveness probe (`409 machine is not idle`).

**The important finding of the day (machine-side symptom, tool-side
cause):** after the kernel takeover tests, forgectrl's supervisor reported
NO MOTION on its liveness probe, ran the rail-off ladder (5/15/30 s), and
once ended in `motion-fault` - the driver-wedge signature. The cause was
`cnc/motor_lock=15` left behind by the takeover drills (they mask every
axis and never restored the mask), and the supervisor's probe does not
reset the mask: its steps were masked, so no motion by construction. Real
probes read head-accel p2p 1779-2857; the masked ones 144-480; the two
"MOTION OK" ladder recoveries seen under the mask (p2p 541 and 718)
were false positives against the fixed `>=500` threshold, plausibly the
rail re-energize jolt. Two consequences: (1) **the rule, from the
operator: every test starts from, and leaves, the fresh-boot idle state
(atomic clean start), and the baseline is taken after a reboot** - the
runner now brackets every test and bench tool with a baseline pass
(`forgetest/baseline.py`, contract in `docs/ACCEPTANCE.md`), takes a
fresh-boot reference once per boot, and takeover runs capture the
controller-owned kernel attributes on entry and write them back before
forgectrl restarts; the fresh-boot dump of this image (uptime 235 s)
confirmed the fixed values (`motor_lock 8`, `x/y_mode 8`, `x/y_decay 1`,
`step_freq 28160` - the controller's tick, not the probe's 10000 -
`ramp_rate 125000`, hold currents 33/5, lamps and button LEDs 0, heater
and TEC off). A reference dumped at uptime 30 s on 2026-08-16 showed the
probe values instead (`motor_lock 0`, `step_freq 10000`, `y_mode 1`): the
dump raced the controller's init writes - `/mode` reports `running` at the
spawn, not at the config - so `boot_reference()` now waits for the
controller's markers (`step_freq`/`motor_lock`/`y_mode` at their fixed
values, bounded 20 s) before dumping, and retakes a pre-config reference
while the boot is still fresh. Proof: k1-k2 / k3 / fire-abu re-run under the baseline -
counters (0,0,0) before and after, the probe verified in 3 s after every
takeover, no ladder, `post: clean` every time. (2) Two forgectrl items
for the operator's decision, not changed: the liveness probe should write
`cnc/motor_lock=0` for its move (a leftover mask from any tool must not
read as a wedge), and the `P2P_MOVING >= 500` threshold has little margin
over the noise floor seen today (~480) against a real-move signature of
~1800+ - a settle after the rail-on before sampling, or a threshold near
1000, would keep a false MOTION OK from starting a controller on a dead
machine. Also noted: at a fresh boot in GRBL mode `pic/lid_led` is 0 and
nothing in the GRBL stack lights the lid lamp; the lit bed the bench was
used to is cloud mode's `LLvl=132`, which persists across the switch back
to GRBL - a resting-lamp setting in forgectrl would be a product
decision. (Later the same day the operator power-cycled the machine and
the fresh-boot reference read `lid_led=132`: the PIC lights the lid lamp
at power-on; the dark lamp after my soft `reboot` was the module's remove
path. The reference is therefore taken after a **power cycle** -
`docs/ACCEPTANCE.md`.)

**Same day, after the power cycle, campaign `c-20260816181534-d07a`:
22 of 26 - everything but the four live-laser tests.** The motion group
under the baseline: `motion.pacing` (idle CPU 2.7 %, moving 34 %, parked
2.7 %, hold/resume exact), `liveness-probe`, `cancel-abort` (jog cancel
16.8 mm short of 40, `^X` abort mid-move into Alarm with position
retained, `$X`, return drift 0.000), `jog-roundtrip` (8 jogs, peak 10500
mm/min, hold parked, drift 0.000, operator confirmed the gantry) and
`deadman` (SIGKILL respawn 1.3 s, SIGSTOP -> kernel underrun 0.21 s with
the latch locked, forgectrl restart mid-move: the busy controller
finished unmanaged and supervision was retaken at idle);
`cooling.fans-quiet-after-motion` (idle profile back 30 s after M9);
`cloud.mode-switch` (session established 2 s after the switch, back to
GRBL Idle) and `cloud.gfhome-homing` (`$H`, homed in 50.5 s, corner
confirmed). Tool findings fixed on the way, each a real bench lesson:
grblHAL's Idle precedes the machine's by the stream depth and the decel
tail, so motion tests now end on forgectrl's idle; a soft reset (`^X`)
flushes the controller's read buffer and eats a `?` that lands in it, so
the Grbl client re-sends `?` until a report arrives; a killed controller
still reads as running until the supervisor reaps it (wait for a
different pid); a forgectrl restart mid-move ends in a **replace-at-idle**
- stop the unmanaged controller, hold the device, re-probe, start a
supervised one - because the old inherited fd cannot be adopted
(SERVICES.md now says so; the test expected the same pid); the cloud
session's evidence is gfcloud's own authenticate/ws-connect lines, not
the optional firmware-probe file; cloud mode's connect zeroes the kernel
counters at the head's start and its hunt homes the head 245/139 mm to
the corner - the test tells the runner and jogs the head back. Two
product observations left visible as baseline leftovers: `$H` (gfhome)
and cloud mode leave the lid lamp at 236 (gfhome should hand the lamp
back; the mode-switch test hands it back itself because it caused the
switch), and a mode switch back to GRBL keeps cloud's lamp level. The
first `Idle`-before-motion race also lived in the fans-quiet test's
second wait (harmless there). **The operator then ran the four live tests
from the page - `laser.emission-witness`, `disarm-in-hold`,
`expected-stop`, `kill-mid-fire`, all PASS - and exported: 26 of 26,
*Release authorized*, and `scripts/acceptance-gate.py` authorizes the
image's own manifest with the artifact. That was an exercise of the
release mechanism, not a release: no `releases/v…` directory was
committed.** Two observations from the live runs, both restored by the
baseline: each live test left the head a few mm +X of its start (11 /
2.8 / 3.3 mm - the tests should end on a return jog), and
`kill-mid-fire` left `cnc/streaming=1` (the supervisor's controller-exit
safing writes `cnc/stop` and the latch, not the streaming flag; the
respawned controller manages the flag per run, so it is hygiene, not a
hazard - noted for the safing sequence).

**Same day, the forgectrl changes decided from the campaign - landed,
built in the forge-yocto tree, hot-deployed on the bench (forgectrl
`ff9a7c9` + `c8f6558`, recipe pin bumped in `1d9b553`):** (1) the lid lamp
has a resting policy - the `lid_lamp_idle` setting (0-255, default 236,
Settings > Lid lamp), asserted at daemon start, on a settings change
(live), and at every controller spawn, so a warm reboot no longer leaves
the bed dark and a cloud session's level does not linger; the camera
engine owns the write (a running lid capture applies it at teardown). (2)
The liveness probe writes `cnc/motor_lock=0` for its move (a leftover
mask from any tool must not read as a wedge), settles 300 ms after the
run-current step before sampling (the current step jolts the head), and
the moving threshold is 800 (live >= 1040, typically 1800-2900; the
rail-on / current-step jolt up to ~700). Proof, through the acceptance
tool: `forgectrl.settings-bounds` (lamp resting at 236, 256 / -1 /
"bright" refused, 100 applied at once, cleared back to 236) and
`motion.liveness-probe` (every axis masked, forgectrl restarted, the
fresh probe MOTION OK on the first try at p2p 2047/1341, mask cleared by
the controller's init). The baseline expects the lamp at the setting now
(the boot capture is the record, not the lamp reference), and its settle
waits for the controller to be running - the post pass had run between
the probe's own writes and the controller's init writes once. **Images
`20260816191838` (forgefirm-image, v0.1.0, 192.7 MB rootfs) and
`20260816191951` (forgefirm-image-dev) are built on that tree - forgectrl
`c8f6558`, the day's forgetest, acceptance identity `c72448c2…` equal on
both - and archived under `images/20260816191838/` with checksums (the
previous pair, `215236`/`215332`, under `images/20260815215236/`).**

**2026-08-16, dev image `20260816191951` flashed: every test came up
`domain-changed`, none inherited - the expectation above ("every domain
forgectrl does not touch inherits") was wrong, and the tool was right.**
The two dev-image manifests differ in exactly one platform field:
`platform.layers.meta-forgefirm.content_sha256` (`b2d13d87…` →
`7ef5555d…`); machine, kernel modules and DTB hashes are equal, and the
only components that moved are forgectrl (7 files) and the dev-only
forgetest. The only non-`.md` change in `meta-forgefirm` between the two
builds is the one-line SRCREV bump in `forgectrl.bb` (`1d9b553`) - the
layer is content-hashed into the platform identity, the platform is
folded into every fingerprint, so the pin bump counted as a platform
change and invalidated the whole catalog. Structural, not a fluke: every
component update that ships in an image rides a pin bump in a
content-hashed layer, so under that rule every image with any component
change was an invalidate-all and the per-domain inheritance the contract
promises could never hold across images (the component entry already
carries the change file by file; the pin double-counted it). Fixed the
same day: component pins live in `<recipe>-pin.inc` (SRCREV + the PV that
moves with it, nothing else) and `forgefirm-image-manifest.bbclass` leaves
`*-pin.inc` out of the layer content (`FORGEFIRM_MANIFEST_PIN_SUFFIX`),
mirrored in `scripts/manifest-from-tree.py` and proven by
`forgetest/tests/test_tree_manifest.py` (pin bump → hash unchanged; recipe
body change or a pin written into the recipe → hash changed, the safe
direction); the six component recipes (forgectrl, grblhal-glowforge,
forgefirm-app in meta-forgefirm; kernel-module-glowforge,
python3-gfhardware, python3-gfutilities in meta-openglow) require their
pin files and resolve the same SRCREV/PV under bitbake. A second, smaller
contributor stays as designed: a test's implementation hash is its suite
module, so the day's edits to `suite/{cloud,cooling,forgectrl,kernel,
motion}.py` alone would have re-required 16 of the 26. **Consequence for
the bench: the fix changes the layer content itself, so the first image
built with it is a platform change against everything recorded so far -
that image's campaign is a full one, unavoidably; from then on a
component pin bump re-requires only the tests covering that component.
Run the full campaign on the first pin-file image, not on `191951`.**

**2026-08-16, bench-tab ports complete (item 15b).** Every tool that can
run against the machine is now runnable from the bench page: the scope
tools (`pwm_sweep`, `pwm_hold` - now a takeover with a locked-state guard:
the latch relocked, refused if FIRE or LASER_ON reads active;
`pwm_stream_test` with a PASS/FAIL exit), the flow characterization
family (`flow_characterize`, `flow_recheck_char`, `flow_warm_validate`,
`flow_matrix` as takeovers - forgectrl owns the thermal hardware, so the
page's takeover replaces the tools' own controller stop/restart, whose
command line predated the supervisor; `flow_sustained`, `fan_test` and
`temp_calibrate` stay dry), the escalation drill (`cool_confirm_max_s`
shortened through forgectrl's settings and restored; the setting's
minimum, 60 s, is the default budget) and the live drills (`<drill> [S]
[F]`, all six, the token from the board). The host tools keep working
from a workstation: `scripts/bench/gfbench.py` resolves `GF_HOST` (host
mode, ssh) or the board itself (local mode; the page runs them that way
with `GF_HOST=127.0.0.1`, `GF_TOKEN`, and their data files under
`/data/forgetest/bench/`). Not ported, by nature: the two null-sink CI
harnesses and the `.puls` decoder. Proof: `forgetest/tests/
test_bench_registry.py` (registry <-> `scripts/bench` consistency, every
ported tool builds its command line, every script compiles, gfbench host
and local modes), the server test (a scope tool runs inside the takeover
wrapper; the bench environment reaches the tool), and a local-mode smoke
run on the bench (`temp_calibrate.py watch`, `gfbench.setting`, the
token) staged in `/tmp` and removed. **The ported tools themselves have
not been exercised from the page on the bench yet - that rides the next
dev image (the confirmation campaign's image).**

### Tool status record

**Release acceptance tool (forgetest) - BENCH-VALIDATED 2026-08-16.**
Contract: `docs/ACCEPTANCE.md`; catalog v1 (26 tests, coverage lint
enforced in CI, rule in `CLAUDE.md`). The full catalog ran on the
dev image `20260815215332` through the tool - takeover, motion,
cooling, camera, cloud, and the live tests from the page - to 26 of
26 and an export the gate authorizes against the image's manifest;
the campaign rules (domain-scoped inheritance, the always-required
core, FAIL/ERROR closing a campaign, implementation and component
changes invalidating exactly their domains) behaved as specified
across the day's closures; the baseline rule was added on the way
(record in "Release acceptance" above). The flash of `20260816191951`
exposed the layer-hash over-invalidation (a component pin bump counted
as a platform change; fixed - pins in `<recipe>-pin.inc`, left out of
the layer content; record in "Release acceptance" above). The catalog
has since grown to **35 tests** (item 16's parity work, then a sweep
that merged the tests sharing a setup: `kernel.fire-line` runs A/B/U
and the mid-ramp unlock behind one takeover, `laser.armed-kill` covers
the expected stop and a SIGKILL on one scrap setup,
`laser.pause-resume-lid-cancel` pauses, resumes and then cancels one
armed burn, and `cloud.lid-interlock-abort` runs the lid and the
interlock as two prints; the 17 `auto` tests were left separate, since
merging them buys no operator time and costs failure isolation).
Every board-runnable bench tool is ported to the page, including
`resume_dark_lead.py`. Remaining: the first release runs the campaign
and commits `releases/v<version>/acceptance.json` - **not yet: no
release is cut.**

## 2026-08-16 … 2026-08-17 — lid / button / interlock parity

### The parity record

**Lid / button / interlock parity with the factory firmware — DONE,
bench-validated 2026-08-17 on dev image `20260817124714`.** Both controller
modes react to the lid, the remote-interlock loop and the button the way the
factory daemon does. The factory behavior was decoded and then recorded on
the bench machine booted into factory 2.6.0-2228; that session covered five
prints and its measured numbers are in the facts bank in `BRINGUP.md`.
- **What the machine does, both modes.** Lid or interlock open during a job,
  running or paused: motion stops within milliseconds of the edge, the job is
  **cancelled and not resumable**, the head returns to the position the job
  started from **with the lid still open**, the kernel laser latch relocks and
  the armed window closes. The next job re-arms with a button press — the same
  press the hardware button latch needs, so the software window and the
  hardware latch agree by construction. The return-home park ignores the lid
  and always runs to completion. A lid or interlock open during the pre-run
  button wait cancels the job with the reason named. A lid open during a hunt,
  homing, a jog or at idle is ignored. The button pauses and resumes a job:
  in cloud mode with the factory's laser-off backtrack and resume lead
  (`cloud_pause_backtrack_ticks` 2000 / `cloud_resume_lead_ticks` 1950), in
  GRBL mode as feed hold / cycle start — the kernel refuses a backtrack on a
  live-streamed ring, so a resumed GRBL cut picks up where the deceleration
  ended. A pause is not a cancel: the latch stays unlocked and the armed
  window open across it. `lid_policy = hold` selects stock grblHAL door
  behavior (park in Door, cycle start resumes) instead of the cancel.
- **GRBL** (`grblHAL-glowforge/src/glowforge_switches.c`, `glowforge_laser.c`):
  the arm wait cancels on lid or interlock with a clean soft reset — no alarm,
  reason reported — and a press with the lid open never arms; the button is
  the pause/resume toggle outside that wait, the arming press consumed so it
  is never also a pause; a lid or interlock open mid-job parks the job through
  the core's door state (planned deceleration, spindle off, position kept) and
  the driver then cancels it, resets from the parked state and enqueues a
  `G53 G0` back to the job start with the door hidden and the latch locked.
  The job start is the machine position at the Idle → Cycle transition.
  `GF_SWITCH_FILE` is the file-backed EV_SW word that lets null-sink builds
  drive these edges in CI.
- **Cloud** (`python3-gfhardware/gfhardware/machine.py`, `Glowforge-Utilities`):
  the interlock joins the lid in every gate; the switch thread wakes the run
  loop on the edge, with the level read kept as a backstop; the park ignores
  the lid and the cancel flag and clears the ring before it moves, so nothing
  of the abandoned job plays ahead of it; a hunt ignores the lid; a job refused
  at start ends `:cancelled`, never `:completed`; the button pauses and resumes
  a print exactly as the factory does (`print:paused` / `print:resumed`), and a
  lid, interlock or service cancel while paused cancels from where it stands.
- **No resume dwell.** The GRBL resume was suspected of losing its first ~90 ms
  to the HV_ENABLE re-arm. Measured on the pads instead
  (`scripts/bench/resume_dark_lead.py`, numbers in the facts bank): the chain
  is back within ~3 ms of the resume and motion only restarts ~219 ms later, so
  there is nothing for a dark dwell to cover and none was added.
- **Proof.** Host: `laser_arm_test`, `laser_lifecycle_test.py` (button wait,
  lid and interlock in the wait, button toggle, cancel + return without alarm,
  `lid_policy=hold`), `python3-gfhardware/tests/test_machine_lid_button.py`,
  the gfutilities suite, and the forgetest unit tests + coverage lint. Bench,
  through the acceptance catalog: `motion.button-hold-resume`,
  `motion.lid-cancel-home` (cancel from Run and from a hold),
  `motion.interlock-cancel-home`, `motion.lid-policy-hold`,
  `cloud.lid-interlock-abort`, `cloud.lid-during-button-wait`,
  `cloud.hunt-lid-open`, `cloud.pause-resume`, `cloud.pause-cancel-paths`,
  `cloud.gfhome-homing` and `cloud.mode-switch` all PASS 2026-08-17; the live
  arm-wait, mid-burn lid cancel, expected stop and armed-kill drills passed
  the same day (`laser.arm-wait-lid`, `laser.emission-witness`,
  `laser.disarm-in-hold`, and the mid-burn lid cancel that the stream-engine
  fix below made honest).
- **The stream-engine defect this work found and fixed.** A mid-burn lid
  cancel reported a return the machine never made: the park's `cnc/run` landed
  while the kernel was still playing the hold's queued tail, was refused with
  EPERM, and "refused, kernel running" was taken for a start — the kernel then
  idled with the park bytes stranded, and the next run played them first. Fixed
  in `stepper_stream.c`: a refused run stays *pending* and is re-issued the
  moment the kernel reads idle; a soft reset never stops a kernel that is only
  draining a completed stream; a mid-motion reset clears the unplayed residue
  once the stop has played out, before any new bytes ship or the device changes
  hands; the cancel path waits for the drain before the reset. The lesson is in
  the catalog: the lid tests check the **kernel counters**, not grblHAL's
  belief about them, and the baseline refuses to jog while unplayed ring bytes
  exist.
- Items 4 and 12 above are closed by this policy.

### The controller safety mapping it replaced

**Controller safety mapping — DONE.** The mid-job Door hold described
here is the `lid_policy = hold` path; the default is the factory-parity
cancel of item 16 (lid or interlock = cancel + return to the job start),
bench-validated 2026-08-17 (`grblHAL-glowforge/src/glowforge_switches.c`). The
controller reads EV_SW with `EVIOCGSW` from the protocol thread's
realtime hook (no grab — forgectrl polls the same device) and maps:
- **doors (bit 3) not closed, or interlock (bit 5) loop open →
  the core's `safety_door_ajar`.** A running job parks in the door
  state and resumes when the condition clears, which is what the
  hardware chain already does to the beam. Bit 3 is the series
  combination the safety chain itself uses, not the individual door
  switches.
- **hv_enable (bit 4): never gated on.** It is the readback of the
  chain's HV_ENABLE output (facts bank in `BRINGUP.md`), telemetry only; the
  core's `e_stop` capability is not advertised. (The `estop_halts_motion`
  opt-in that existed until 2026-08-15 is gone, together with the
  name — see the facts bank.)
- **interlock latch (bit 6): deliberately not gated on.** Its
  resting state on a healthy machine is not characterized and a
  false assertion would wedge every job; the hardware chain enforces
  it regardless.
- No switch device (host builds) = no capability advertised, no
  signals.
**N5 answered: no software latch-reset path is needed.**
Interlock-trip recovery was exercised in commissioning runs without
one — the chain recovers when the condition clears. `cnc/laser_latch`
stays write-only (1 = lock), the driver's arm flow unlocks per job,
and `interlock_latch_reset` remains a readback. **Amended 2026-08-15:**
the *interlock* latch never trips at all in ForgeFIRM — see Next work
item 11; the "recovery" seen in commissioning was the software
safety-door path, not the hardware latch.
**Bench items:** open the lid mid-job (expect `Door` at the sender,
motion parked, cycle start resumes after close); a Pro with an
unjumpered interlock connector (expect the same door behavior);
confirm no spurious door events across a full job. Underrun → alarm
was already covered by the stream-fault path.
**Changed 2026-08-15 (grblHAL a9446fe, host-tested, pin bumped, bench
validation pending):** the door signal is now hidden from the core while it is
IDLE, JOG or HOMING (`gfsw_visible`, applied to both `get_state()` and
the edge delivery) and delivered the moment it is in any other state.
Reason: a lid cycle at idle — every material load, and a power-up with
the lid open — left grblHAL parked in `Door:0` until a cycle start,
and LightBurn then sat at "Waiting for connection". Consequences: jog
and `$H` are allowed with the lid open (beam hardware-blocked; upstream
"ignore when idle" semantics), a job started with the lid open parks on
the first poll, mid-job opens park exactly as before, and the cloud
client (own EV_SW reader) is unaffected. Bench check: lid open/close
at idle → state stays Idle; open mid-job → Door, close, `~` → resumes;
Start with the lid open → Door immediately. **Partly validated
2026-08-15 on image 20260815154622: LightBurn now connects after the
lid has been opened and closed at idle (the original complaint).**
The mid-job and start-with-lid-open checks are still open, and the
session surfaced further LightBurn door-open issues — see Next work
item 12.

## 2026-08-17 — step timing under CPU contention

Opened by an operator report: the `LB-GF-OG-FM` LightBurn job, GRBL mode
at 2000 mm/min and 30 % power, ran jerky and lost many steps.
`cnc/underruns` and `cnc/faults` both read 0 throughout, which is the
whole reason the condition had gone unnoticed — the kernel ring never
runs dry, so the stream stays continuous and only its *timing* is wrong.

### What was wrong

The board runs one core. Of grblHAL's four threads only the shipper held
`SCHED_FIFO`; the producer — which advances virtual time and stamps every
step onto the pulse grid — ran `SCHED_OTHER` at nice 5, the same class and
nice as forgectrl's MHD connection threads. forgectrl was measured at
~41 % of the core serving the panel's MJPEG camera stream, one connection
thread alone at ~35 %.

When the producer's virtual clock falls behind the ship cursor,
`gf_stream_pulse` clamps late events forward and the backlog ships one
step per machine tick: 28 160 steps/s against the 1 778 that 2000 mm/min
asks for, a ~16× velocity burst no motor follows.

The margin absorbing a stall was **2 ms**, not the 200 ms queue depth it
appears to be: the shipper's due index carries the same `+ gf.depth` the
producer's base starts at, so the two cancel and the pacing lead is the
only slack there is.

### What was changed

- Producer on `SCHED_FIFO` one priority below the shipper, and `core_mx`
  given priority inheritance — the producer holds it across the stepper
  callback while the protocol thread also takes it, so promoting without
  PI would have traded jitter for unbounded inversion (grblHAL 026c169).
- Producer lead made tunable (`GFSINK_LEAD_MS`) and defaulted to 10 ms;
  the per-run `LOG_DEBUG` line now reports the **measured** `min margin`
  in ms against it (grblHAL fd059b3).
- Clamp count reported per run at `WARNING`, not only cumulatively at
  process exit.

The lead defaults to 10 rather than higher because of the cycle-churn
path: `gf_stream_wakeup` re-bases production onto the wall cursor only
when the cursor has passed it, so a larger lead survives an idle gap,
skips the re-base and accumulates as dark padding. Measured on the
`laser_stream_test.py` churn harness: 2 ms and 10 ms both give an
identical 64 790-byte stream, 15 ms and above inflate it to ~225 k and
stop being deterministic.

### Bench record

Two `motion.step-timing-under-load` runs 90 s apart on image
20260817210307, same campaign, camera streaming at 2592×1944 in both,
plus the test's own nice-5 CPU hog:

- **PASS** — 20 legs, 26.7 s, 0 clamps. Camera not streaming.
- **FAIL** — 20 legs, 26.7 s, **7 runs clamped, 81 events**, max behind
  3.9–4.4 ms. Camera streaming.

That isolates it: `SCHED_FIFO` covers a userspace CPU competitor and does
not cover the camera, whose per-frame cache maintenance over a 4.8 MB
non-coherent capture buffer is kernel-context work no userspace priority
can preempt.

On image 20260817220126 with the 10 ms lead, same conditions as the
failing run (camera at 2592×1944 **and** the CPU hog): **PASS, 0 clamps**,
worst `min margin` 4.9 ms of 10 across 12 legs.

Then the original `LB-GF-OG-FM` LightBurn job again, operator-run, with
the video stream live (independently corroborated: forgectrl was holding
`video0`/`video4` with four `:8080` connections mid-job):

    run: 686850 callbacks in 62.255 s (90.6 us/call incl. pacing),
    50721 pace sleeps, max behind 4.7 ms, min margin 3.1 ms of 10, clamped 0

Identical callback count and duration to an earlier run of the same job,
so it is the same work. Operator judgment: ran clean. `underruns` 0,
`faults` 0, and no clamp warning from the current controller instance.

### What the numbers say

`max behind` is **not** the instrument — it read 0.0 ms on every leg of
the passing acceptance run while the real margin fell to 4.9 ms, because
the producer never falls behind its own wakeup epoch; the margin is
consumed by the offset between that epoch and the shipper's `ship_t0`.
Only the measured `min margin` shows the condition.

The real job is the harsher adversary: 3.1 ms of 10 remaining, against
the synthetic test's 4.9 ms, at a *lower* callback rate (11 033/s vs
13 784/s). Real cut geometry costs more headroom than uniform jog legs.

So the fix holds on the job that prompted it, with ~31 % of the budget
left at the worst moment. Both remaining levers are unspent: camera
capture resolution (the mainline `ov5648` offers 1280×960 and 640×480
binned modes, 4.1× and 16.4× fewer bytes, which shortens the stall rather
than merely spacing stalls out) and the churn re-base (which is what
would allow a lead beyond 10 ms). Tracked in BRINGUP "Next work" item 16.

## 2026-08-17 — the laser duty threshold ladder

The first owed step of "Next work" item 17: measure where the tube starts
lasing, so `$35` can stop M4's velocity-scaled power falling below it.

### The run

`live_fire_drills.py pthresh 1000 300` on wood scrap, operator-run on dev
image `20260817220126`, machine idle and homed, coolant 23.9/24.1 °C. The
precondition was read off the machine first: `$30`=1000, `$31`=0, `$32`=1,
**`$35`=0.0**, `$36`=100 — no floor in place to lift the rungs.

Thirteen rungs, 2 %…30 % of full, 25 mm each at F300, constant power (M3),
3 mm of `+Y` between them. Before firing, the two conversions were checked
against each other: a rung of *P* % sends `S = 10·P`, which the core maps to
`floor(127·P/100)` counts, and `$35 = P` computes `min_value =
(uint)(127·P/100)` — the same integer, so the rung's percent *is* the `$35`
value exactly, not approximately.

### What came back

Material, counting from the first rung drawn: rung 1 (2 %) nothing at all;
rungs 2–9 (3–14 %) a tiny spot at the start of each line and a dark line
after it; rungs 10–13 (16–30 %) continuous marks.

The `hv_current` trace agrees independently. It holds 0 for 19.5 s (arm
wait), then runs nonzero to 82.8 s, immediately before Idle. Within it the
laser-off `G0` between rungs reads 0, so the current runs count the rungs:
**12 segments of ~4.7 s at a ~5.27 s period, not 13.** The last segment ends
at the job end, so it is rung 13; counting back 12 puts the first current at
rung 2. Rung 1 drew no measurable discharge current — the same rung that
left no mark, from a completely separate witness.

So the tube has **two thresholds, far apart**:

| | rung | duty | witness |
|---|---|---|---|
| Discharge strikes | 2 (3 %) | PWMSAR 3 | current lifts off; spot only |
| Sustained lasing | 10 (16 %) | PWMSAR 20 | first continuous mark |

Between them, 3–14 % is a **dead band**: current flows and climbs (per-rung
means 133 → 289 raw) with essentially no light out. Each line's opening spot
is the strike transient; the tube lights, drops below lasing gain, and coasts
dark for the remaining 25 mm.

This falsifies the drill's own guidance, which said the current "lifts off
baseline at the same rung the material starts marking" — lift-off is rung 2,
marking is rung 10. The docstring and the printed read-the-material text were
corrected to name both thresholds and to tell the operator that a rung
showing only a start-of-line spot is *below* the threshold, not at it.

Raw `hv_current` is a presence/absence witness only. Per-rung means are
non-monotonic at the top (429 at 20 %, then 311 and 302) and the variance
collapses on the top two rungs, which is what an aliased point-sample of a
pulsed current looks like; the signal has no characterized transfer function.

### Ruling out the firmware explanation for the spots

A start-of-line spot is also what a full-power leak would look like: a kernel
run start resets the hardware duty to ~100 %, so a fire bit reaching the
stream ahead of its power byte would burn at full power. The material already
argued against it — rung 1 is the first fire of the run, the likeliest place
for such a leak, and it is blank — but the stream is the record, so
`laser_stream_test.py` gained a fourth session (rule 10): a ladder in the same
shape, full power deliberately absent, asserting that every FIRE tick rides a
commanded duty and that the fire ticks divide evenly across rungs (a rung
opening at its neighbor's duty shows up as a surplus on one and a deficit on
the next).

Result on the native build: duties under FIRE were exactly `[22, 23, 26, 32,
41, 52]`, nothing else, and **28296 fire ticks on every rung, identical to the
tick**. No full-power window, no stale-duty window. The spots are the tube and
supply, not the firmware.

### What landed

- `DEFAULT_SPINDLE_PWM_MIN_VALUE 16.0f` in `boards/glowforge.h` — the
  measured lasing rung. Chosen over the next rung up (20 %) because the floor
  is spent at corners, where velocity and dose per unit length already move
  the wrong way, and because `$35` is a user setting anyone can raise.
- The harness now derives its expectations from that floor (`duty_for()`), so
  the M4 session's S500 plateau moved 63 → 73 and its ramp `[44, 52, 63, 127]`
  → `[57, 64, 73, 127]`, plus a new check that no duty under FIRE falls below
  the floor. All four sessions pass, as do `switch_map_test`, `laser_arm_test`
  and `laser_lifecycle_test`.
- `laser.power-floor`, an auto acceptance test (the suite's only non-firing
  one): reads `$$` and checks the machine actually carries the commissioned
  floor, since stored settings beat freshly baked defaults and a machine with
  an older EEPROM needs `$RST=$` once. Coverage lint clean at 40 tests.

### What it means for the model

The usable analog range is 16–100 %, about 6:1, with the bottom sixth of the
control range physically dead — and the factory's captured pulse files pin the
power byte at 127 and modulate dose by dithering the FIRE bit at 6.5–18.8 %
density. The dead band is why. `$35` is a patch that buys freedom from dropout
by putting its full 16 % into every corner; dose set by pulse density cannot
fall below the lasing threshold by construction. Item 17 is now the density
model itself, with the analog path as the fallback.

## 2026-08-17 — how the factory sets power

Three cloud-mode cuts of the same 1" square, same location, same material,
same speed, changing only the Glowforge UI power setting: Precision Power 1,
Precision Power 100, then Full Power, with the pulse file captured from each.

Pulse-file capture ships off (`LOGGING.SAVE_PULS`), and the machine's copy of
`/data/etc/gfhome.conf` predated the key, so it was enabled for this session
and turned off afterward. A first attempt appended the key past the last
section, where `get_cfg('LOGGING.SAVE_PULS')` would never have found it — it
belongs inside `[LOGGING]`, and was verified through the app's own parser
rather than by eye.

### The measurement

**Analog duty is not a power control.** All three runs carry the power byte
exactly three times, always 127: once as the cut begins, then a refresh every
~27 000 ticks (~2.7 s). Nothing modulates PWMSAR, at any setting.

**Dose is FIRE-bit density on a fixed 7-tick period** — 700 µs at
`STfr` = 10 000, ~1.43 kHz — with the on-count dithered between adjacent
integers:

| Setting | on-runs | mean of 7 | density |
|---|---|---|---|
| Precision Power 1 | 1 (×359), 2 (×212) | 1.371 | 0.1953 |
| Precision Power 100 | 5 (×236), 6 (×334) | 5.576 | 0.7952 |
| Full Power | continuous | 7 | 0.9965 |

The period was exactly 7 in all 570 measured cycles of both dithered runs, and
the mix of adjacent on-counts matches the fractional part exactly: PP 1 wants
1.371 on-ticks, and 2-runs are 212 of 571 = 0.371. That is an error
accumulator, not a repeating pattern.

**The power setting never reaches the machine.** The three headers are
identical — no key differs — so the model lives entirely in the service, which
bakes it into the FIRE bits. The motion is identical too: 5420 steps,
101.62 mm (4 × 25.4), 10.81 s at 9.44 mm/s. Full Power's file is longer only
in the lead-in before the cut.

**Velocity compensation is real but partial.** Density falls as the head slows
into a corner, by the same relative factor at every power setting
(corner/cruise 0.38, 0.38, 0.41). Measured per step interval, though, fire
ticks per step *rise* from 3.89 at 9.44 mm/s to 7.00 at 1.22 mm/s, so dose per
unit length still climbs ~1.8× at a corner — against the ~7.7× it would climb
with no compensation at all. Only ~24 of 5420 step intervals are below cruise
speed, so the direction and rough magnitude are solid and the exact law is
not.

On the UI scale, PP 1→100 is linear in density (~0.006 per unit, intercept
~0.189); Full Power sits off that line, where PP ~134 would land, which fits a
setting the UI presents as outside the normal range.

### Two corrections to earlier readings

The first pass at the dither sampled the mid-point of the cut, which for a
square is a corner, and truncated its distributions — it showed 8-on/4-off
bursts that are corner behavior, not the steady pattern. The first pass at the
dose law counted every tick as a step, because in this encoding bits 1 and 3
are *direction*, held for the whole side, and only bits 0 and 2 are step
pulses; the tell was 2026 mm of travel on a 101.62 mm cut.

### A defect found by using the feature

Deleting the capture directory under a running gfcloud showed that with
capture enabled, a missing directory or a full disk makes `load_motion` raise
on the capture write and kills the print. A debug aid must never cost a job:
the capture open, the per-chunk write and the `.info` write are now each
non-fatal, dropping the capture with a warning and running the job on
(`gfutilities`, with a regression test in `tests/test_lifecycle.py`; verified
in three cases — missing directory still loads the job, a writable directory
still gets the copy, capture off writes nothing). No acceptance-catalog
consequence: the path is an off-by-default debug capture with no bearing on
emission, motion or the release surface.

## 2026-08-17 — the density dose model, phases 1 and 2

Implemented and host-proven; off by default, so nothing about a shipped
machine changes until `laser_power_model = density` is set.

### The change

The whole hot path is one predicate in the shipper:

    if(gf.cur_fire)          ->   if(gf.cur_fire && (!gf.dith_period || dither_tick()))
        b |= 0x10;                    b |= 0x10;

That `&&` is the safety property, structurally: the model masks the core's
fire state and can never be a source of one, so it stays out of the safety
argument entirely — the armed window, the latch, the coolant gates and the
hardware chain are all upstream and untouched.

Around it: a fixed base period of `laser_pulse_ticks` (default 20 = 710 us
at 28160 Hz, the factory's ~1.43 kHz), on-count `level x period / 127` with
the remainder carried across periods so finer densities average out, the
on-ticks leading each period so a level renders as one burst rather than
isolated ticks. The accumulator resets only where the dose itself restarts —
run boundary, fire off, disarm, abort — never per segment. In density mode
the duty is pinned: a power byte still leads every kernel run, because the
run start resets the hardware duty, but it always carries full duty and a
level never reaches PWMSAR. Selected per arm from the shared machine config
and reported as `laser armed (density)`; the arm warns when `$35` is set,
since the floor only clamps the light end of a range that cannot fall into
the dead band anyway.

### What the harness holds (rules 11-13)

- Density renders the commanded level exactly: levels 2, 3, 7, 15, 25, 38
  came back as 0.0158, 0.0237, 0.0551, 0.1182, 0.1969, 0.2993 against
  level/127 of 0.01575, 0.02362, 0.05512, 0.11811, 0.19685, 0.29921.
- S1000 renders density 1.0000 and still ends dark.
- Every power byte carries full duty; a level change inside a run costs no
  stream byte, where analog ships one per level (4 bytes, duties 0/30/52/84,
  against density's 1).
- The mask invariant, measured rather than argued: the same job run under
  both models produced an identical motion grid tick for tick, and all
  20051 density FIRE ticks fell inside the 169776 the analog run fired.
- Churn (planner-starve run boundaries) still terminates dark under the
  model, with no FIRE across a stepless gap.

The analog path is byte-identical to before the change — same byte counts,
duties and fire ticks on every pre-existing session — so the fallback is
intact.

### Two things the work turned up

**Spindle `$`-settings take effect at controller start, not at the write.**
The core precomputes the S -> duty mapping once, when the spindle is
enabled; a settings write does not re-run it. After a runtime `$35=0` the
shipped duties stayed floored at 57/64/73/127. So `$35=16` set on the bench
earlier today persisted immediately and was reported by `$$` immediately,
but only entered force at the next controller restart — which the capture
work then supplied. The harness now models this the way an operator would:
one launch writes the setting, the next runs the job.

**A laser state change made while the stream is idle was lost — found,
root-caused and fixed.** Reproduced in both dose models, so it was not the
density model's doing: with a line-at-a-time sender and moves long enough to
drain the planner, `S100 / G1 X5 / S300 / G1 X5 / S600 / G1 X5` fired only
the first move and shipped duty 30 three times.

It was two faults wearing one symptom, and fixing the first exposed the
second. `gf_stream_laser()` dropped transitions while nothing was streaming,
so nothing re-asserted the state for the next run, which a run end leaves
dark — the stream engine now records the state the core last asked for
whether or not it is streaming, and re-asserts it at the first byte of the
next run, fire only inside an armed window (an abort clears it, so a closed
window can never be resurrected). With that in, all three moves fired, and
all three fired at duty 30: the level had never reached the driver at all,
because `spindleSetState` discarded its `rpm` argument. Per-segment updates
carry the level inside a laser block, but an S executed between blocks
arrives only through that synchronous path. It now publishes the duty, and
only the duty — fire stays where `spindleUpdatePWM` and its gates put it,
so the new path carries no consent to fire.

Rule 14 in the harness is the regression: the same standalone-S job must
show each level firing its own move. It does — 28338 fire ticks each at
duties 30, 52 and 84, where before the fix duty 30 held all 85014 and the
two other levels never appeared.

## 2026-08-17 — the density ladders, and the minimum pulse

Four live ladders on one piece of scrap, 8 rungs each from 5 % to 100 % of
dose at constant power: base period 20, 40 and 10 ticks at F300, then period
20 again at F100. The same six rungs marked every time — 20 % and up. 5 % and
10 % never marked in any of the four.

### Pulse length is not the variable; average power is

Because the same pulse length occurs at different densities across the
periods, the runs contain matched pairs:

| pulse | density | period | marked |
|---|---|---|---|
| 107–142 µs | 20 % | 20 | yes |
| 107–142 µs | 10 % | 40 | no |
| 36–71 µs | 20 % | 10 | yes |
| 36–71 µs | 10 % | 20 | no |

Hold the pulse and halve the density: the mark goes. Hold the density and
vary the pulse 3×: nothing changes. Feed does not move it either — 10 % at
F100 carries 0.0567 dose/mm against 20 % at F300's 0.0394, **44 % more energy
per millimeter than a rung that marks**, and it still left nothing. Two
independent variables moved without shifting the boundary. What sets the
low-end marking limit is average power reaching a quasi-steady surface
temperature; going slower does not help, because the heat conducts away
between pulses.

So the base period can be chosen on other grounds, and stays at 20.

### The trace separates two different failures

The F100 run carried the `hv_current` trace (`pthresh` printed one, `dladder`
did not until this run — the omission cost the three F300 ladders their
per-rung witness). It shows **seven** current segments for eight rungs:
boundaries at 36.6, ~52.0, 67.3, 82.5, 98.0 and 113.2 s, each segment
14.4–14.9 s, one 25 mm rung at F100. The fire window is 106.8 s where eight
rungs would need 121.6 s.

The final segment anchors the count: 113.5–128.4 s reads 943–986 dead flat,
the saturated steady current of continuous fire, which can only be 100 %.
Counting back, the segment means rise monotonically — 182, 320, 330, 390,
450, 540, 967 — for rungs 10 % through 100 %. Rung 1 has no segment at all:
its fifteen seconds are the zeros before 21.6 s, indistinguishable from the
arm wait because nothing happened in them.

| rung | outcome |
|---|---|
| 5 % | **no discharge at all** |
| 10 % | discharge for the full 15 s, no mark |
| 20 %+ | discharge and mark |

Supply current is not light — `pthresh` already showed this tube drawing
current across a whole band while emitting nothing — so "10 % struck" is not
"10 % lased". But 5 % not striking is unambiguous, and it is ours to fix.

### The factory's own numbers, for scale

Precision Power 1 runs the power byte at 127 (PWM duty 100 %) and a **FIRE
duty cycle of 19.53 %** — 1.371 on-ticks of every 7-tick window. Fitting the
three captures, the factory maps its entire 1–100 scale onto density
18.9–79.5 %, with Full Power off that line at ~99.7 %. Its "1 %" is the
bottom of the band that does useful work, not 1 % of the physical range —
which is why no user ever meets the dead zone. Older captured factory
jobs run 6.5–18.8 % density, so 18.9 % is a product
decision about cutting, not a physical floor.

### The fix: a minimum pulse width

At 5 % the model emitted one-tick stubs, 36 µs, and the supply did not
strike. The factory never emits below one 100 us tick and reaches low density
by skipping windows instead. `laser_pulse_min_ticks` (default 3 = 106 µs)
does the same: when the computed on-count falls below the minimum the period
is skipped and the **whole** debt carried, rather than a stub emitted. The
debt is conserved, so the average density is untouched.

Measured on the stream, level 2 (density 0.0159):

| | bursts | density |
|---|---|---|
| minimum 1 tick | 444 × 36 µs | 0.0158 |
| minimum 3 ticks | **147 × 106 µs** | 0.0159 |

147 × 3 = 441 against 444 — the same energy as fewer, longer pulses, and
every level already above the minimum is bit-identical, so the change touches
only what it must. Rule 15 in the stream harness holds both halves: no burst
below the minimum (excepting one clipped by fire going off mid-burst), and
the rendered density still exact.

### The fifth ladder, and a conclusion retracted

Same ladder, period 20, F300, with the 3-tick minimum in place. **The floor
moved down a full rung: only 5 % failed to mark, and 5 % now strikes.**

The trace carries eight current segments where the F100 run had seven.
Segmenting by time rather than by zeros — at 5 % density the sampled current
aliases, so isolated zeros appear mid-rung and cannot serve as boundaries —
the rung period is 5.25 s and lines up end to end: fire begins at 6.2 s,
exactly at rung 1's start, boundaries fall at 11.4, 16.6, 21.9, 27.3, 32.6,
38.1 and 43.3 s, and the span is 42.0 s against 41.4 s for eight rungs. The
final segment reads 937–981 flat and saturated, which can only be full
density. Rung 1 shows peaks of 291, 286 and 204 where the F100 run held a
flat zero for the rung's entire fifteen seconds.

**This retracts the conclusion in the entry above.** Pulse length is not
irrelevant: 10 % moved from no mark at F100 — with three times the dose per
millimeter — to a mark at F300, at the same density, the only change being
its pulses growing from 36–71 µs stubs to 106 µs. The matched-pairs argument
was sound but drawn entirely from comparisons at or above 20 % density, where
every pulse length in play was already sufficient; it generalized from the one
regime where pulse length does not bite. Above ~100 µs dose governs, below it
pulse length does, and below ~36 µs the supply does not strike at all. The
factory's 100 µs quantum sits exactly on that boundary.

Not read into: the low-rung current means (76 and 82 raw for 5 % and 10 %).
At those duties a 3.3 Hz point sample of a pulsed current carries
presence-versus-absence and nothing more. Noted as a confound, though it cuts
against the result rather than for it — this ladder started at MPos 0,0 after
the controller restart, so it may be on different material than the stacked
Y=0/24/48/72 runs.

### The sixth ladder: a longer minimum is worse, and why

`min_ticks = 6` (213 µs), same ladder otherwise. **It broke 5 % striking** —
seven current segments again, boundaries at 14.5, ~19.85, 25.2, 30.4, 35.9
and 41.1 s, segments 4.4–4.9 s with none double-length, fire spanning
9.5 → 46.0 s = 36.5 s against 41.4 s for eight rungs, and the flat saturated
tail anchoring rung 8. Seven rungs marked, matching.

The arithmetic explains it. Below the minimum the model emits `min` ticks
every `min/on` periods, so the interval between pulse starts is

    interval = min_ticks × tick / density

and **the base period cancels** — which retroactively explains why periods
10, 20 and 40 gave identical results in the first three ladders. At 5 %
density that is 2.26 ms at `min_ticks` 3, which struck, against 4.51 ms at 6,
which did not. Doubling the minimum doubles the gap as well as the pulse, and
the gap is what decides: the discharge is re-struck each pulse and past
roughly 2–4 ms it has decayed too far to catch.

That also puts `min_ticks` 3 at the factory's own operating point — its 6.5 %
engrave jobs place 100 µs pulses 1.54 ms apart, against 1.64 ms for
`min_ticks` 3 at that density — and puts 6 outside anything the factory does,
in the direction that fails. The bench is back at 3.

**Measured band for this tube: strikes from ~5 %, marks from ~10 % at F300.**

Which closes the pulse-structure route to a usable 1 %. The interval grows as
1/density, so 1 % implies an 11 ms gap, five times what already failed — no
pulse shape reaches down there. The low end is a scaling problem.

### The seventh ladder: the scale, and the goal met

`$35 = 10` — a density floor under this model, not a duty floor — with the
ladder reweighted to the bottom of the user scale (1, 2, 5, 10, 20, 40, 70,
100 % of S), since with a floor in place what matters is whether the lowest
levels a user can dial in still mark.

The mapping puts S onto 9.4–100 % density, so a commanded 1 % lands at 10.2 %,
just above the ~10 % marking floor the earlier ladders measured. **All eight
rungs marked.** The trace carries eight current segments — boundaries at 14.3,
19.5, ~24.85, 30.2, 35.4, 40.9 and 46.1 s, fire spanning 9.1 → 51.1 s = 42.0 s
against exactly 8 × 5.25 — with means climbing monotonically:

| rung | commanded | density | mean current |
|---|---|---|---|
| 1 | **1 %** | 10.2 % | 136 |
| 2 | 2 % | 11.0 % | 190 |
| 3 | 5 % | 13.4 % | 214 |
| 4 | 10 % | 18.1 % | 262 |
| 5 | 20 % | 27.6 % | 331 |
| 6 | 40 % | 45.7 % | 340 |
| 7 | 70 % | 72.4 % | 444 |
| 8 | 100 % | 100 % | 968 flat |

So the original goal is met: a user's 1 % is a real, visible mark rather than
silence, and 100 % is full power. It took the density model to make every
level real pulses, the minimum pulse to keep them strikeable, and the floor to
put the user's range on the band that works — the same three pieces the
factory uses, arrived at from this bench's own measurements.

### The defaults flipped

`laser_power_model` now defaults to `density` and `$35` to 10, so a stock
machine runs the model and a commanded 1 % marks. The analog path stays as an
explicit `laser_power_model = analog`.

The two settings are coupled and the pairing matters: `$35` is a **density**
floor under the shipped model and a **duty** floor under the fallback, wanting
~10 and ~16 respectively, and the wrong pairing is a dead band in either
direction. The arm warns on both mismatches — a zero floor under density,
where the bottom of the S range asks for pulses too far apart to re-strike,
and a sub-lasing floor under analog.

Test-side consequences worth noting, since the default reaches into the
harness: every analog session in `laser_stream_test.py` now selects its model
explicitly rather than inheriting it, or the flip would have silently turned
them into density runs and taken the analog fallback's coverage with them.
`laser_arm_test` asserts the inverse of what it used to — no config key now
means density — and `laser.power-floor` carries the new floor and its
PWMSAR minimum. All ten stream sessions, both C harnesses and the lifecycle
harness pass on the new defaults; the analog duties shift exactly as the new
floor predicts (min_value 12, gradient 0.115).

Owed: validation at a production feed. Every ladder behind these defaults ran
at F300 or F100 at constant power, so none of them exercised M4's velocity
scaling into corners, a real sender's mid-run level changes, or the raster
path, which has not run at all. The arithmetic says dotting will not be the
problem — at 10 % density the pulse interval is 1.07 ms, 35 µm at
2000 mm/min against a ~200 µm spot — but that is reasoning, not a cut.

## 2026-08-20: how the factory reports progress (F1)

The open question behind cloud-mode progress reporting was which carrier the
factory uses and how often: a `<action>:progress` event, a `progress_bytes`
query on the action endpoint, or the periodic settings report. The strings in
the factory binary named all three and settled none. It was answered by
observing the factory application's own cloud session on the machine, running
the factory slot end to end (a hunt, images, five motions, and a print with a
button pause and resume).

The answer is none of the three as posed, because two of them collapse into
one. Progress rides an **outbound WSS `type:"progress"` frame**, machine to
service, and that frame **is** the periodic settings report: its
`settings.values` block is exactly `periodic_settings_tags`. No
`<action>:progress` event and no `progress_bytes` query appeared in the whole
session. Cadence is `progress_update_interval_ms` = 30000, i.e. one frame every
30 s during a cut, with a burst at each phase transition; during the cut
`current` advances at the 10 kHz print tick.

Two things fell out of the same capture. `CCbp` in the frame reads the byte
position (1009 against a `current` of 994), re-confirming it as telemetry and
not the pause constant an earlier reading had guessed. And the factory's own
progress `total` grew during the cut, 33,291,208 → 33,553,352 → 33,815,496,
256 KiB per interval, because the factory live-appends to its ring: even the
factory's progress bar divides by a denominator that is still growing. Under
ForgeFIRM's streaming feed a progress report must divide by the feeder's own
job total, never the kernel byte counter. That is the F2 work; the carrier,
the frame shape and the cadence are now known.

The decision that came with it: the `type:"progress"` frame is carried as a
deliberate exception to the telemetry exclusion. It is a UI status update, not
the sensor firehose, and it is the operator's only sign a multi-hour print is
advancing. The write-up is in `CLOUD.md` ("Progress reporting" and the scope
exception); the plan's F1/F2 rows are updated. The pause is also reported by
the factory as a ten-event phase machine against the two ForgeFIRM sends, noted
there as optional polish on the F2 work.

## 2026-08-20: the campaign behind a print longer than the ring

The work that made a cloud print independent of the ring size ran from
2026-08-18 to 2026-08-20 and is finished, so the plan it ran from is retired
into this entry and the durable documents. What follows is how the result was
obtained, which is the part that does not belong anywhere else.

**It started from a wrong belief.** The ring was 16 MiB and a job that did not
fit was going to be refused with a clean message, on the reasoning that the
factory must refuse one too. Re-reading the factory application against the
Ghidra project said otherwise on every point. Its ring is 32 MiB, allocated
through `dma_alloc_attrs` out of a 320 MiB CMA area with no device-tree pool
and no module parameter. It models the downloaded body as a pulse data source
with a cursor, gzip or plain behind one vtable, and stages it into the ring in
segments that are checked against free space, refusing with `-ENOMEM` rather
than writing a partial chunk. And it does not stop when the ring is full: it
starts the job and keeps appending for as long as the job lasts.

**The proof was on the machine already.** This board's own factory logs, kept
across slot switches on the shared `/data`, carry a 107 MB job played through a
32 MiB ring. Nothing needed to be induced; the factory had already done it and
written it down. A capture of the factory's own cloud session later showed the
same behavior on the wire, its progress `total` growing 256 KiB per interval as
it appended.

**So ForgeFIRM streams too**, and the shape follows the factory's: hold the
compressed body in memory and inflate only as far as the ring asks, which keeps
a three-hour job to a few MB and off the eMMC entirely; fill the ring before
the button is offered, so a job that cannot be loaded fails before the laser is
ever armed; declare the live feed to the kernel only when the job actually
outran the ring, so a job that fits behaves exactly as it always did; top up on
`-ENOMEM`; clear the live-feed flag after the last byte, so the real
end-of-data is a completion rather than a starved ring. The ring itself moved
to 32 MiB, at factory parity, through a size-aligned no-map device-tree pool.

**Two defects surfaced in the building.** A dry ring used to end the run loop
with `aborted=False`, which reported a job that stopped mid-cut as completed;
it aborts now. And the pause on a streamed job could not retrace, because the
old bound deducted the retained gap from a budget that was zero under a
topped-up feed, counted bytes enqueued rather than bytes played, and set its
dead stop a whole program back instead of one ring back. The retained gap *is*
the backtrack history, which is what the kernel now publishes as
`max_backtrack`, and a request longer than that is refused rather than quietly
shortened.

**What the campaign settled along the way**, each recorded where it belongs:
the factory reports progress on a `type:"progress"` frame that is the periodic
settings report; `CCbp`/`CCbt` are reported progress rather than the pause
constants an earlier reading took them for; and `CFrh`, `CCwp`, `CCrp` and
`CCup` have no consumer in the factory at all, so there is nothing to drive a
warm-up or a rest off. The contract is `kernel-module-glowforge/UAPI.md`, the
client behavior is `CLOUD.md`, and the tag findings are in the firmware
reference alongside the captures.

**What it cost to be sure:** the pulse decoder was 41x too slow to keep a ring
fed (a `sorted()` per byte, 32 kB/s against the 1.33 MB/s it manages now), and
that only showed up when a real 53 MB job was replayed through a fake ring
rather than a synthetic one. The job that hung the bench is kept as the
regression fixture.

## 2026-08-21: a lid cancel that went back to the wrong place

`laser.pause-resume-lid-cancel` failed its first run on the dev image of
2026-08-21 with "head not back at the job start (drift 14.925 mm)", and at the
bench the job had looked right: the button paused the cut, the button resumed
it, the lid stopped it, and the head came back. It came back to the wrong
place. The kernel counters agreed with the controller's own position report:
Y exactly where the job began, X 14.925 mm along the first leg, which at F200
is about four and a half seconds of cutting, the moment the pause landed.

**The controller had told the truth by its own bookkeeping.** The driver takes
the job start as the machine position at the Idle to Cycle transition, and the
grblHAL core restarts a held cycle by passing through Idle: `state_await_resume`
sets Idle and then Cycle back to back, so every resume from a feed hold was
recorded as a new job beginning where the hold had stopped. The lid cancel then
returned the head to the pause point and reported "returned to the job start",
which was exactly what it had written down.

**The fix is a definition.** A job is under way from that first transition
until the core is Idle with the planner empty (the program ran out, a stop, a
reset) or in an alarm. A resume passes through Idle with the planner still
loaded, so it is the same job and keeps its start; a job abandoned in a hold
and reset is over, and the next one starts where it starts. Both sides are
held by the null-sink lifecycle harness now, which reproduced the bench
failure to the millimeter (returned to X=13.088, the pause point) before the
fix and returns to X=0.000 after it.

**Why the acceptance test caught it and the eye did not:** the test measures
the return against the position it recorded before the job, not against the
controller's message. An operator watching the head come back has no such
reference, and fifteen millimeters on a forty millimeter square reads as
"back". The test stays as it is.

## 2026-08-21: the first full campaign on a pin-file image

Completed. Dev image `20260821181036`, the first built on the
`<recipe>-pin.inc` layout: 42 of 42 satisfied (12 run on that image, 30
inherited under the domain model from the day's earlier dev images), all
eight `cloud.*` tests run on that image, and the export reads "Release authorized:
YES" for that image's manifest (campaign `c-20260821182204-dc01`, exported
2026-08-21T18:40:30Z, artifact sha256 `6f17f690...43273055`). No release is
cut from it.

## 2026-08-21: cooling.gate-off, first bench run

PASS on dev image `20260821210903`, campaign `c-20260821213027-0b47`, at
21:47:16Z: the coolant ceiling set to 6 C tripped `OVERTEMP` (hold, fire
blocked) one second into its run session; set to 60 C the next session read
`OK` with `gates_off` `["coolant_max"]` on `/cool/status` and `/status` and the
run-start line in the forgectrl log; restored to 33/31 the third session read
`OK` with nothing off, the settings back verbatim.

The first attempt on the same image (21:18Z) failed in the test, not the
engine: its M9 and the next M8 were 300 ms apart, the GRBL client reports
level-triggered at 1 Hz and the engine samples at 1 Hz, so the engine never
saw the session end and never re-read the ceiling; the restore-on-failure
then rewrote the file without opening a session, which left the bench
holding `OVERTEMP` against the test's ceiling until the next job. The fixed
test (forgefirm f274eb1) waits for the engine's phase to leave `run` after
every M9 and cycles a session after restoring; it was hot-deployed to the
board for this run and is in the next dev image.

## 2026-08-21: the job's limits pass through, seen on a live session

`cloud.pause-resume` PASS on dev image `20260821220926` (campaign
`c-20260821222752-4d93`, 22:30:52Z), the first print under the header
pass-through. The two logs together, from the same session:

- Every hunt and motion file the service sent carried a coolant window of
  10 to 50 C; the client derived `coolant_max_c=50.0 coolant_min_c=10.0`
  from each, and the engine answered `effective limits: coolant ceiling
  33.0 C (local 33.0, header 50.0)` with `header coolant ceiling 50.0 C is
  not stricter than the local 33.0 C; the local one stands`.
- The print carried `air_assist_min_rpm=116 coolant_max_c=33.0
  coolant_min_c=5.0` (the captured cut-job values: `AArx` 64500 us, `CMrx`
  33000, `CMrn` 5000); the engine resolved the ceiling at 33.0 (equal to
  the local one, so the local stands) and published the floors (coolant
  5.0 C, air assist 116 rpm, exhaust and intake 0) for the gates to come.
- At the job's end the limits left with it and the effective set fell
  back to local.

Two refinements from the run, neither a behavior change: the "not
stricter" notice printed twice per job (forgectrl e0b41b3 names it once per
value), and the test quoted the session's first job-limits line, a hunt's,
where the print's is the one worth keeping (it now takes the first line
after the print's action request).

## 2026-08-22: the fan floors measured, and a hunt that would have tripped them

`fan_floor_measure.py spinup` (bench page `fan-floor`, 120 s at the cut
profile from idle, GRBL mode, the exhaust duct's inline booster fan off, so
the exhaust worked against more back pressure than a normal cut):

| fan | steady rpm | min | max | sd | t90 |
|---|---|---|---|---|---|
| exhaust | 11638 | 11444 | 11947 | 103 | 5 s |
| intake 1 | 4157 | 4102 | 4193 | 12 | 7 s |
| intake 2 | 4158 | 4128 | 4173 | 6 | 7 s |
| air assist | 11048 | 11029 | 11061 | 8 | 1 s |

Purge current 627 at idle and 625 at run duty: the engine holds purge air on
continuously, so both are the "on" reading (the off reading, ~1, is from an
earlier observation). The floors shipped from this: exhaust 6400, intake
2290, air assist 6000 rpm (55 percent of steady, bands 50 to 60 percent),
purge current 300, grace 15 s (twice the slowest time to 90 percent). The
provisional floors had come from a snapshot at a lower exhaust speed; the
measured margin is larger.

The run also sent the first `/cool/status` with the limits and the fan rows
through a 512-byte reply buffer, and then a 160-byte limits fragment: twice
a cut-off document, found by the measurement tool refusing to parse it.
Both fixed in forgectrl with a host test that renders the widest legal
document and parses it (`tests/coolfmt_test.c`).

Reading the measurement through cloud mode found a defect in the gates as
first built: the service reports every action as a run, and its hunt and
motion headers command the exhaust and the intakes off and the air assist
at idle, so a hunt longer than the grace would have tripped `AIRFLOW` at
any floor. Decision (operator): a fan is judged only at the operating
point its floor was measured at: always while the laser is armed, when a
job's profile may raise a fan but never lower it below the run duty; and
unarmed when commanded at the run duty. A hunt is measured, published as
`unjudged`, and not judged. `cloud.mode-switch` now watches the connect-time
hunt's gate rows for it.

Both tests ran the same day on a hot-deployed forgectrl (the working tree
cross-built and installed over dev image `20260821230723`; informational,
not acceptance). `cloud.mode-switch` PASS: the hunt reported two run ticks
with the exhaust off and `unjudged`, verdict `OK` throughout.
`cooling.fan-gate-trips` FAIL first, for two reasons worth keeping: the
run-start tick resolved the effective limits before it reloaded the
settings, so for one tick `gates_off` named the exhaust while its row still
carried the old floor (fixed: the session start re-resolves the limits after
the reload, so rows, `gates_off` and the log line agree); and the test's
2 s grace, chosen against the provisional 1800 rpm intake floor, now let
both intakes trip at ~1850 rpm on their 7 s spin-up (the test grace is 8 s).
Rerun PASS in 59 s: only the exhaust tripped in the exhaust leg, only the
purge in the purge leg, the exhaust read `off` with floor 0 in the off leg,
and the restore showed every fan `ok` at the shipped floors (exhaust 11723,
intakes 4157 and 4162, air assist 11078 rpm, purge 628 counts).

## 2026-08-22: the measured floors and the operating-point rule on a pinned image

Dev image `20260822135848` (forgectrl 47e4256 pinned by forgefirm adcd1ad;
release `20260822135751` built alongside), flashed after a fetch-verified
both-image build. Campaign `c-20260822140659-2f25`, every auto test the
pin bump invalidated plus the rest of the non-operator, non-live catalog:
**18 of 18 PASS** (cooling.flow-verify, image.health, kernel.latch-locked-idle,
kernel.k1-k2, kernel.backtrack-bounds, forgectrl.auth,
forgectrl.settings-bounds, forgectrl.panel-serves, logs.tree-tail-export,
logs.level-settings, motion.deadman, cooling.fans-quiet-after-motion,
cooling.gate-off, cooling.fan-gate-trips, camera.sensor-profile,
camera.frame-health, cloud.mode-switch, kernel.fire-line).

The two that carry this change, as recorded: `cooling.fan-gate-trips` in
58 s with only the exhaust `TRIPPED` in its leg, only the purge in its,
the exhaust `off` at floor 0 in the same tick `gates_off` named it, and
the restore reading exhaust 11726, intakes 4160 and 4193, air assist
11095 rpm, purge 627 counts, every gate `ok` at the shipped floors;
`cloud.mode-switch` in 29 s with the connect-time hunt's run tick reading
the exhaust at 0 rpm, `unjudged`, the air assist `unjudged`, verdict `OK`
throughout, and the hunt finishing `:completed`. The hunt's run phase is a
few seconds long and gave one sample at a 1 s poll, so the watcher now
samples twice a second.

## 2026-08-22: the unplugged-exhaust-fan drill

The gate on the real failure path, not a settings override: the operator
unplugged the exhaust fan's whole connector at the Interconnect PCB (fan
dead, tach silent), the machine idle in GRBL mode, lid closed, nothing
armed. One `M8` session from the board, `/cool/status` read once a second
(dev image `20260822135848`):

- 1 to 14 s: every gate `grace` (the shipped 15 s), exhaust reading 0.
- 15 and 16 s: exhaust `under` at 0 rpm; intakes, air assist and purge
  `ok`, up to speed inside the grace.
- 17 s: verdict **`AIRFLOW`**, `fire_ok false`, `hold true`, exhaust
  `TRIPPED`, reason `AIRFLOW: exhaust 0 under the 6400 floor for 3 s -
  hold, no resume this job`; the other four fans held at run duty around
  the dead one. grblHAL relayed the reason on the Grbl port as a
  `[MSG:Warning: ...]`, and forgectrl logged the `WARNING` line.
- `M9` ended the session into the smoke-clear phase with the fault still
  named; the operator replugged the connector.
- The next `M8` session: exhaust 4112 rpm at 1 s, 6623 at 2 s (past the
  floor), 11640 at 7 s (the measured time to 90 percent), `ok` with every
  gate at the end of the grace, verdict `OK`, clean end.

One observation for a decision: between the two sessions the engine sat
at idle with the verdict still `AIRFLOW`, `hold=true`, `fire_ok=false`.
The fan fault latches for the run session and clears at the next session
start, the same shape as the fire alarm; at idle the hold cancels GRBL
jogs and the cloud client's print pre-check refuses a print before a
session could re-prove the fan (a hunt clears it). Decision (operator,
the same day): the fault ends with its session, since every session
judges every fan afresh after the grace before anything can fire;
`cooling.fan-gate-trips` now checks the verdict is `OK` with no hold once
the tripped session is over. The fire alarm keeps its idle hold. Built
and flashed the same day (dev image `20260822145201`, forgectrl d51dbdb):
`cooling.fan-gate-trips` PASS in 60 s, the engine reading `OK`, no hold,
fire allowed in the smoke-clear phase right after the tripped session.

## Superseded status notes

### Shared machine services — remaining polish, as listed 2026-08-13

**Shared machine services — remaining polish.** The consolidation
itself is complete and drilled (see "Where the project stands" and
`forgectrl/docs/SERVICES.md`); these are the deliberate leftovers,
none of them blocking:
- **Diagnostics as engine modes.** The Diagnostics flow tools still
  drive the thermal hardware themselves while the cooling engine
  suspends its writes and publishes fire-blocked. The check
  parameters and factory duties are already shared (`cool.h`, one
  definition for both), so what remains is folding the tools into
  the engine as modes and retiring the suspend/resume dance.
- **Rail policy** (SERVICES.md "Pulse-device ownership", the one
  `[contract]` item left there). `cnc/enable` / `cnc/disable`
  are not forgectrl-only writes yet: under the broker no client
  drops the rail any more, but the GRBL driver still writes
  `cnc/enable` at init and at homing resume — idempotent, since the
  rail is already up and settled, so this is tidiness rather than a
  bounce source. (An idle-rail-off policy is not part of this: the
  rail stays up while the machine is on, per the wedge model in the
  facts bank.)
- **Busy-state arbitration under one lock.** forgectrl's idle/busy
  gates (`POST /settings`, `/mode`, diagnostics start, upload/apply)
  each cross-check `machine_is_idle()` and `update_job_running()` at
  their own call sites. They fail closed and are drilled, but a
  single arbiter (one lock, one "who owns the machine right now"
  answer) would replace N targeted checks with one and close the
  remaining request-interleaving windows by construction.
- **HTTP surface caps.** The daemon relies on MHD's default connection
  ceiling (a 500-connection flood plateaued at 379 fds under the raised
  4096 `RLIMIT_NOFILE`, no crash, `cnc/state` readable throughout).
  An explicit `MHD_OPTION_CONNECTION_LIMIT` plus a per-IP cap is the
  right hardening, and the camera `ensure_engine` `popen()`s should
  move out of the HTTP callback so a slow media-ctl can never stall the
  request thread. Changing the MHD start flags touches the streaming
  model, so this waits for a bench slot of its own.
- **Cloud per-job fan profile.** The cloud client passes the pulse
  header's `AArd`/`EFrd`/`IFrd` duties to the engine as the per-job
  run profile. Homing headers are verified end to end (they carry
  the idle-quiet profile the factory uses — no fans during a hunt);
  a real print header's duties should be confirmed through the same
  round trip at the next cloud print.
- **`/cool/status` cosmetics.** The endpoint echoes the last
  reported `armed` flag even when that report is stale
  (`report_age_s` tells the truth), and a gfcloud homing session
  reports every motion as a job, so the engine cycles run → smoke →
  idle per motion. Both are silent and safe — the homing profile
  keeps the fans at idle duties — but motion actions reporting
  `idle` would be more honest.
- **Button edge detection.** The GRBL arm flow reads the button as
  an EV_SW level; edge detection belongs in that reader. It does
  not change where the button is read (per-mode direct evdev, for
  latency) — the switch map itself is contract-documented and
  shared.

### Camera service — closed 2026-08-03

**Camera service: DONE 2026-08-03, bench- and operator-verified**
(see "The camera service" section above; LightBurn streams it
directly). Remaining camera work: lens calibration / bed alignment,
the deferred 5.6 emulator homing-image smoke.

### Housekeeping entries

**Housekeeping**: ~~pick the controller's remote home~~ **DONE
2026-08-02** — the controller is now the canonical driver repo
`github.com/ScottW514/grblHAL-glowforge` (+ `ScottW514/core` fork;
the settings-write crash fix is upstream PR grblHAL/core#999; repoint
the submodule to upstream when it merges). ~~Yocto recipe for
grblHAL-glowforge~~ **DONE 2026-08-03** (`grblhal-glowforge` in
meta-forgefirm, boot autostart, reboot-verified). ~~Documentation
sweep (CLAUDE.md charter, README roadmap, INSTALL/BUILD/kas README)~~
**DONE 2026-08-13.** Remaining: kas flip + first GitHub release per
kas/README.md once ready to publish.

## Reference notes

### Head-IRQ source validation — the beam-emission hypothesis

- **Head-IRQ source validation — beam-emission hypothesis: OPEN
  (exploratory feature; NOT a first-light prerequisite).** The
  EV_SW `head` bit (GPIO3_22, factory pad name HEAD_IRQ; the
  panel's "Head sense" row) is the head MCU's attention line —
  idle LOW with a healthy head attached (measured 2026-08-08); it
  pulses on head reboot (hence the 60 ms DT debounce) and floats
  to the SoC pull-up with no head driving it, so the raw level is
  NOT a presence signal (presence = the head answering at I²C
  0x47). The factory app answers this IRQ by reading the head's
  interrupt flags over I²C, and the only flag register is the reg
  0x05 RO group — bit0 hall_sensor, bit1 accel_irq, bit2
  beam_detect_digital (head_private.h) — so there are exactly
  three candidate IRQ sources; working hypothesis (operator): the
  in-cut source is the head's IR beam-emission detector — digital
  flag 0x05 b2 + analog level reg 0x16 (both already head sysfs
  attrs), tunable detection model at regs 0x22–0x2a
  (lambda_k/lambda_t/theta_r/theta_t/e_t = the factory
  BDlk/BDlt/BDtr/BDtt/BDet settings; regs defined in
  head_private.h, not yet exposed as attrs).
  Priority/scope (operator, 2026-08-08): later exploration, not a
  must-have —
  - The bench head is **gen2** (a first-round Kickstarter unit
    already shipped gen2). Gen1 heads are presumed rare to
    nonexistent in the wild, though the factory images still
    support them, so some must be assumed to exist. The gen1
    board-level beam chain (!BEAM_DET GPIO4_15, !BEAM_DET_XOR
    GPIO4_08, !BEAM_DET_TIMEOUT GPIO4_07, BEAM_DET_ERR GPIO4_10 —
    DT-pinmuxed, not driver-requested; BEAM_DET_LATCH_RST GPIO7_13
    pulsed at cut start, boards v13/v14 only) is documented here
    as legacy reference only.
  - Whether the factory actually USES beam detect is unknown. The
    v2.6.0 factory app carries a complete but config-gated
    subsystem (separate printing/idle enables, severities
    failing-abort / pausing-alert / silent-alert, level-vs-edge
    trigger option, beam_detect_irq + irq_override, fault report
    upload; an invalid severity defaults to DISABLED), so the
    plumbing exists but production enablement is an open question.
    Detection at low fire energies is also unverified — the sensor
    may simply not trip on a low-power pulse.
  - Same status for the accelerometer: a promo-touted factory
    feature that was not active in early releases and may not be
    today. Its data path is direct (lis2hh12 on the I²C bus) but
    its INT pin routes to the head MCU as flag 0x05 b1, so it is
    also a head-IRQ source.
  Cheap opportunistic check during live-fire bring-up (no gating):
  log EV_SW head-bit edges + head/beam_detect_digital/_analog
  while firing — if the beam flag level-holds the IRQ, the panel
  row asserts during sustained emission. Later-feature decisions
  if it pans out: beam-absent-while-FIRE as an optional fault
  input, attrs for the calibration regs, panel row relabel (e.g.
  "Head IRQ / emission").

### Homing: limit switches planned, the accelerometer approach retired

- Limit-switch homing remains the planned second method; the
  accelerometer approach stays retired (implementation and bench
  record in grblHAL-glowforge history before commit 26298a3;
  durable accel/rail-contact measurements below).
Durable measurements from the accelerometer spike (relevant to any
future contact/vibration sensing; tools `accel_fast.py`,
`bump_seek.py` remain in scripts/bench):
- **Sensors**: the HEAD accel (lis2hh12) is **i2c-3 addr 0x1e**
  (0x1d on the same bus is a static board part; i2c-0 0x1e is the
  lid). st_accel sysfs one-shots are ~6 Hz and the kernel has no
  IIO triggers; direct I2C (unbind st-accel, CTRL1=0x6F = 800 Hz
  ODR) reads ~530 Hz from Python.
- **Rail-contact signature**: creep baseline ≈0.5–2 k counts;
  contact jumps to 29–42 k within ~4 ms (20–40×). But **slow
  approaches are near-silent** — belt compliance turns slow-speed
  skipping into sub-threshold grinding — so any contact-sensing
  scheme must strike fast.