The stream harness keeps the analog rendering as the host-test
conservatism reference (rule 13's mask, the duty ladders) and drops the
M101 switch sessions; rule 18 stays as the derived-floor proof, now
satisfied from boot by the precompute. The lifecycle harness's
state-files scenario asserts the derived floor is in $$ before any arm.
The catalog's laser.power-model-switch goes and laser.power-floor reads
the one floor key with no M-code needed. The mswitch drill goes; the
m4corner drill becomes a single density pass; the dpatch drill returns
to density only.
The CAMPAIGN-LOG records the first rasters (254 and 508 DPI grayscale
wedges: tonality held to ~14 pulse slots per pixel, no dither artifact,
one benign stale-verdict suppression under CPU starvation) and the
decision that ends the analog mode - the strike transient fires a spot
at every beam-on, and the finish comparison found no advantage. BRINGUP,
LIGHTBURN, MOTION and SAFETY describe the density-only present.
The stream harness gains rules 18 to 21: the floor is derived from the
selected model's config key at the arm and a typed $35 is overwritten;
M101 switches the rendering exactly at the boundary in both directions
with no continuous FIRE at full duty across it; a refused switch (the
spindle on) leaves the stream unchanged, and the harness resyncs with
an empty line because the core skips G-code after an error until the
sender resyncs; M2 reverts a program-scoped switch and Q1 holds. The
analog sessions pin laser_floor_analog at the density floor so the
existing duty expectations stand, and the density ladder's unfloored
run moves from a chained $35 write to the laser_floor_density key.
The catalog's laser.power-floor becomes model-aware: it reads the
configured model and the floor keys from forgectrl, switches to the
configured model with M101 so the derivation runs without a fire, and
expects $35 to be that model's floor. The new laser.power-model-switch
switches to each model with the spindle off, checks the reported
message and $35 after each switch, and checks the M2 revert. The new
mswitch bench drill runs the switch on the machine in one armed run.
Docs follow: BRINGUP's Laser control section describes the switch, the
derived floors and the measured dose response of both models; the
MOTION settings table gains the five keys; LIGHTBURN gains a Power
models section and drops the stale 30 percent floor advice; SAFETY
names the switch's refusal rule; the CAMPAIGN-LOG records the judged
depth-witness runs of 2026-08-30 and the switch's host and bench proof.
The ring and the device-tree pool that backs it are now the size the
factory firmware runs. Docs follow, and the hardware facts bank gains the
reserved-memory map: 511 MiB usable, 96 MiB reserved for DMA, ~454 MiB
left to Linux.
image.health reads the pool size and ring_mb back and fails if they
disagree, so a pool the parameter does not use cannot ship unnoticed, and
checks that free never exceeds the ring less its gap.
MOTION said jogs, homing and hunts were all ungated. Jogs are:
gfsw_visible withholds the door signal while the core is idle, jogging or
homing, so a jog both starts and runs with the lid open. Homing is not.
With homing_mode = gfcloud - the only method that works today - $H hands
the cycle to a cloud homing session, and its move to the home corner is
an ordinary motion action taking the default lid_gated=True: refused with
the lid open, stopped on a lid edge mid-run. Only the lens/Z hunt inside
that session passes lid_gated=False, and that session is also the only
place a hunt happens in GRBL mode - there is no hunt outside one.
BRINGUP gains item 18: GRBL pause and resume should leave no gap in the
cut, the way the factory's does. The beam stops at the start of the hold
(disable_laser_during_hold, on by default), so the head travels the whole
deceleration dark and the resume restarts from a standstill where the
decel ended - an unburned length, then a dwell through the accel that M3
shows as a deeper spot. The kernel waypoint backtrack cloud mode uses is
refused with EPERM on a live-streamed ring, so the equivalent has to be
built above the ring, where grblHAL still holds the planned path the
kernel has already overwritten.
Two wording fixes: the cooling verdict is described as a report rather
than a file, and gfcloud homing as using the machine's builtin
credentials.
Documentation only - no behavior change, so no acceptance-catalog
consequence.
Two pages aimed at someone who owns the machine rather than works on it,
written for the documentation site. Nothing here is new behavior - it is
the behavior the machine already has, explained where an owner can find
it instead of spread across a kernel contract, a services contract and
three driver headers.
MOTION.md follows one thread: everything physical comes out of a single
fixed-tick byte stream, so the page starts there - the byte layout, speed
as step density rather than clock, the ring and the two ways to fill it,
and the hardware's own stop, halt and resume-with-waypoint. The laser is
presented as part of that stream rather than beside it, which is what
makes the three contract rules (power before fire, no consecutive power
bytes, end dark) and the persisting duty legible instead of arbitrary.
Then geometry and limits, device ownership and the liveness check the
operator sees, and the two modes in full: GRBL from connection through
the arming sequence, the stop/pause/fault table and homing-or-not; cloud
from the preloaded pulse file through the pause backtrack, the park that
ignores the lid, and the ring's cap on job length. A comparison table and
the motion-related settings close it.
COOLING.md explains the engine as what it is - one owner of the thermal
hardware answering a single question for whichever controller runs - and
gives the reasons behind the numbers rather than just the numbers: why
the flow check heats and measures the downstream rise, why 40 percent is
the duty (below it, convection mimics flow), why the settle gate uses a
split-half mean instead of peak-to-peak, and why one bad reading is a
suspicion rather than a fault. Over-temperature, the two diagnostics
tools and when to run them, the settings, and a situation-to-response
table. The fire watch is described honestly: the lid IR channels are
first of all a photometer for the lid lamp, the gate ships watch-only,
and it is not a fire alarm.
Both pages state what is not implemented - low-temperature gates, TEC
control, a fire watch that acts, limit-switch homing - so nobody plans
around them. Constants come from the sources that own them (the feeder
contract, cool.h, the board header, the services contract), not from
prose. README links both.
Documentation only, no behavior change and no catalog consequence: docs/
is outside every layer and .md is excluded from the layer content hash.
ScottW514