Prove the dose curve and the recorder; document S-means-light

The stream harness gains rule 19: with the bench-default curve in force
a ladder of S rungs renders the curve's densities exactly (half light
lands near 80 percent density), monotonic, floored and ceiled by
$35/$36; every other session pins laser_dose_curve = off so its
S-to-level arithmetic stays exact, and the arm-report checks carry the
curve name. The lifecycle harness asserts the published state file
names the curve in force. The catalog's forgectrl.panel-serves asserts
the curve field in the grbl report, /curve/status and the ladder
G-code, and its covers name the recorder.

BRINGUP describes S-commands-light through the measured curve and the
owner recorder; the MOTION table gains laser_dose_curve; LIGHTBURN
tells the operator power now means light and how to record their own
tube's curve from the panel.

docs/BRINGUP.md

@@ -238,16 +238,26 @@ spot. The arm report names it (`laser armed (density, floor 10 %)`), and
 a floor of 0 is honored with a note (the ladders run that way). The
 cooling report carries the model with the job state.
 
-**Measured dose response (this bench, 2026-08-30, by the head thermopile,
+**S commands light, through the measured curve.** The tube's output is
-the tube current and the operator's eye on Thick Draftboard and acrylic).**
+convex in pulse density (this bench, 2026-08-30, by the head thermopile,
-Density delivers about half of the CW light at 80 % density, a third at
+the tube current and the operator's eye: 80 % density delivers about
-60 %, a fifth at 45 % and a fourteenth at 30 %: the curve is the tube's
+half the CW light, 60 % a third, 45 % a fifth, 30 % a fourteenth - the
-(pulsed against CW), not the sensor's, and it is the same physics behind
+same physics behind the factory's 18.9 to 79.5 % mapping with Full
-the factory's 18.9 to 79.5 % mapping with Full Power kept apart. An S
+Power kept apart). So the driver maps the commanded fraction through
-correction from that curve (E4 in the working file) is the open item that
+the measured curve's inverse onto the density that delivers it:
-follows. Rasters hold their tonality down to ~14 pulse slots per pixel
+`laser_dose_curve` in the machine config holds density:light percent
-(508 DPI at 6000 mm/min): the dither accumulator's cross-pixel averaging
+pairs, ships with the bench-measured default compiled in, accepts
-recovers the levels, with no visible dither pattern.
+`off` for the identity, falls back loudly on a bad value, and is
+reloaded at every precompute with the arm naming it (`laser armed
+(density, floor 10 %, curve bench-default)`). `$35`/`$36` still floor
+and ceil the result. An owner measures their own curve from the panel:
+the dose-curve recorder hands them a ladder G-code to run from their
+sender - every arm gate stands, forgectrl records the tube current and
+the head thermopile passively, fits the rungs, and Apply writes the
+result (`forgectrl/docs/SERVICES.md`). Rasters hold their tonality down
+to ~14 pulse slots per pixel (508 DPI at 6000 mm/min): the dither
+accumulator's cross-pixel averaging recovers the levels, with no
+visible dither pattern.
 
 An S word takes effect whether or not motion is in progress. Per-segment
 updates carry the level inside a laser block, but an S executed between

docs/LIGHTBURN.md

@@ -152,12 +152,16 @@ restart the controller with the head re-parked.)
 The controller drives the tube the way the factory does: every pulse
 fires at full power, and the power setting decides how many ticks of
 each 710 us period fire. Every power level marks, low levels included,
-because no pulse is ever too weak to strike. The response is not linear:
+because no pulse is ever too weak to strike. The raw response is not
-on this machine 80 % gives about half the light of 100 %, 60 % about a
+linear - 80 % of the pulses deliver about half the light - so the
-third, 30 % about a fourteenth - so pick engrave power by test card, and
+controller maps your power setting through a measured dose curve: 50 %
-prefer setting darkness with speed. Grayscale images fade cleanly into
+commands half the light, not half the pulses. The machine ships with
-the shadows (a low level becomes sparse full-power pulses), and 254 to
+the bench-measured curve; record your own tube's from the control
-508 DPI rasters hold their tonal steps.
+panel (GRBL tab, "Dose-curve recorder": download the ladder file, press
+Record, run the file from LightBurn on scrap, press the button, Apply
+the fit). Grayscale images fade cleanly into the shadows (a low level
+becomes sparse full-power pulses), and 254 to 508 DPI rasters hold
+their tonal steps.
 
 `$35`, the power floor, is set by the controller from the machine config
 (the control panel's GRBL tab, "Laser dose"): do not type it, it is

docs/MOTION.md

@@ -427,6 +427,7 @@ only be changed while the machine is idle.
 | `laser_button_timeout_s` | 300 | How long the machine waits at the button prompt. |
 | `laser_disarm_s` | 60 | Spindle-off grace before the armed window closes. |
 | `laser_floor_density` | 10 | The S-range floor, percent of full: the lowest pulse density that still marks. Loaded into `$35` at every spindle precompute; `$35` is derived, never typed. |
+| `laser_dose_curve` | (bench default) | The measured dose curve as density:light percent pairs; S commands a light fraction and the driver maps it onto the density that delivers it. `off` = identity; a bad value falls back to the default. The panel's recorder measures and applies a machine's own. |
 | `laser_pulse_ticks` | 20 | Density base period in machine ticks (35.5 us each). |
 | `laser_pulse_min_ticks` | 3 | Shortest density pulse in ticks; below it a period is skipped and its debt carried. |
 | `rail_settle_s` | 2.5 | Motor-rail off period when a controller takes the device standalone. |

forgetest/forgetest/suite/forgectrl.py

@@ -222,7 +222,8 @@ def settings_bounds(ctx):
       kind="auto", est_min=1,
       covers=[("forgectrl", "src/ui.*"), ("forgectrl", "src/ui/**"), ("forgectrl", "src/status.*"),
               ("forgectrl", "src/cam.c"), ("forgectrl", "src/main.c"), ("forgectrl", "src/super.c"),
-              ("grblhal-glowforge", "src/glowforge_status.c"), ("grblhal-glowforge", "src/serial.c")],
+              ("grblhal-glowforge", "src/glowforge_status.c"), ("grblhal-glowforge", "src/serial.c"),
+              ("forgectrl", "src/curverec.c")],
       description="The panel page is served, /status carries the machine telemetry the panel and "
                   "the acceptance tool read (including the sys block: CPU busy percent over the "
                   "interval since the previous read, memory used percent), and /cam/status "
@@ -289,9 +290,21 @@ def panel_serves(ctx):
             ctx.check(key in rep, "/status grbl.report lacks %r", key)
         ctx.check((rep.get("laser") or {}).get("model") in ("density", "analog"),
                   "grbl.report.laser carries no model: %s", rep.get("laser"))
+        ctx.check((rep.get("laser") or {}).get("curve"),
+                  "grbl.report.laser carries no dose curve: %s", rep.get("laser"))
         st, text = fc.get("/grbl/settings", raw=True)
         ev["grbl_settings_status"] = st
         ctx.check(st == 200 and b"$35=" in (text or b""),
                   "GET /grbl/settings -> %s without the $$ view", st)
     else:
         ctx.log("no live GRBL controller (%s); grbl block checks skipped", mode)
+
+    # The dose-curve recorder's read surface answers in any mode.
+    st, cs = fc.get("/curve/status")
+    ev["curve_status"] = cs
+    ctx.check(st == 200 and isinstance(cs, dict) and cs.get("state") in
+              ("idle", "waiting", "recording", "done", "failed"),
+              "GET /curve/status -> %s %s", st, cs)
+    st, text = fc.get("/curve/ladder.gcode", raw=True)
+    ctx.check(st == 200 and b"S1000" in (text or b"") and b"M5" in (text or b""),
+              "GET /curve/ladder.gcode -> %s without the ladder", st)

scripts/bench/laser_lifecycle_test.py

@@ -296,6 +296,8 @@ def test_status_files():
         assert '"armed":false' in st, "armed before any job: %r" % st
         assert '"model":"density"' in st and '"floor_pct":10' in st, \
             "model/floor missing (the floor must be derived from boot): %r" % st
+        assert '"curve":"bench-default"' in st, \
+            "the curve in force is not published: %r" % st
         assert '"modals":"[GC:' in st, "modal report missing: %r" % st
         ts0 = float(st.split('"ts_mono":')[1].split(',')[0])
 

scripts/bench/laser_stream_test.py

@@ -61,7 +61,13 @@ over TCP, then checks the dumps against the kernel feeder contract:
  18. the floor is derived, never typed: $35 is loaded from the floor
      key at every precompute, so a $35 typed by the sender is
      overwritten - the ladder renders through the key's floor, and the
-     arm report names the model and the floor in force
+     arm report names the model, the floor and the curve in force
+ 19. the dose curve bends S onto the density that delivers the
+     commanded light fraction: with the bench-default curve in force a
+     ladder of S rungs renders the curve's densities (half light lands
+     near 80 percent density), monotonic, floored and ceiled by
+     $35/$36; every other session runs with laser_dose_curve = off so
+     its S-to-level arithmetic stays exact
 
 The analog sessions select the reference mode through the config; on
 hardware the controller ignores it (density is the only product model -
@@ -169,6 +175,7 @@ JOB_LADDER.append("M5")
 # tube's lasing duty (16), covered by the switch sessions below.
 ANALOG_FLOOR_DEFAULT_PCT = 16.0
 ANALOG_CONF = ("laser_power_model = analog\n"
+               "laser_dose_curve = off\n"
                "laser_floor_analog = %g\n" % PWM_MIN_PCT)
 DENSITY_PERIOD = 20
 DENSITY_MIN_TICKS = 3
@@ -179,9 +186,43 @@ DENSITY_CONF_BASE = ("laser_pulse_ticks = %d\n"
 # analog duty out of the tube's dead band, and here it would just clamp
 # the light end of the range. A floor of 0 is honored as written.
 DENSITY_CONF = ("laser_power_model = density\n"
+                "laser_dose_curve = off\n"
                 "laser_floor_density = 0\n" + DENSITY_CONF_BASE)
 # The shipped density default: no floor key, so the board's floor applies.
-DENSITY_CONF_FLOORED = "laser_power_model = density\n" + DENSITY_CONF_BASE
+DENSITY_CONF_FLOORED = ("laser_power_model = density\n"
+                        "laser_dose_curve = off\n" + DENSITY_CONF_BASE)
+# The shipped default: the bench curve in force (no keys at all).
+DENSITY_CONF_CURVED = "laser_power_model = density\n" + DENSITY_CONF_BASE
+
+# The compiled bench-default curve (glowforge_laser.c curve_default),
+# mirrored here the way the floor is: changing it changes rule 19.
+CURVE_DEFAULT = ((10.0, 0.5), (20.0, 2.0), (30.0, 7.0), (45.0, 21.0),
+                 (60.0, 37.0), (80.0, 50.0), (100.0, 100.0))
+
+
+def curve_density_for(s_val):
+    """The density fraction the bench-default curve maps an S onto,
+    before the $35/$36 clamp (mirrors curve_apply)."""
+    l = s_val / RPM_MAX * 100.0
+    pts = CURVE_DEFAULT
+    if l <= pts[0][1]:
+        return pts[0][0] * (l / pts[0][1]) / 100.0
+    i = 1
+    while i < len(pts) - 1 and l > pts[i][1]:
+        i += 1
+    d0, l0 = pts[i - 1]
+    d1, l1 = pts[i]
+    f = min(1.0, (l - l0) / (l1 - l0))
+    return (d0 + f * (d1 - d0)) / 100.0
+
+
+CURVE_S = (100, 300, 500, 800, 1000)
+JOB_CURVE = ["G91", "G21", "M3"]
+for _s in CURVE_S:
+    JOB_CURVE.append("S%d" % _s)
+    JOB_CURVE.append("G1 X%g F300" % (LADDER_MM if _s % 2 == 0 else LADDER_MM))
+    JOB_CURVE.append("G0 Y1")
+JOB_CURVE.append("M5")
 DENSITY_LEVEL = tuple(int(x * PWM_PERIOD / RPM_MAX) for x in LADDER_S)
 # A $35 typed ahead of the job: rule 18 says the arm overwrites it.
 JOB_DENSITY = ["$35=0"] + JOB_LADDER
@@ -193,6 +234,73 @@ def duty_for_floor(s, floor_pct):
     return int(s * (PWM_PERIOD - lo) / RPM_MAX) + lo
 
 
+# Session H: three levels inside one kernel run. The moves are short and
+# fast so the planner never drains, and each carries its own S word, so
+# the level changes land mid-run. Analog pays a power byte per level;
+# density pays none, because the level rides the FIRE bits.
+JOB_LEVELS = ["G91", "G21", "M3"]
+for _s in (100, 300, 600):
+    for _ in range(20):
+        JOB_LEVELS.append("G1 X0.5 F3000 S%d" % _s)
+JOB_LEVELS.append("M5")
+
+
+# Session I: the levels arrive on their own lines, and the moves are long
+# enough that the planner drains between them, so each S is executed with
+# nothing streaming. The state has no event to ride and must be
+# re-asserted at the next run's first byte.
+IDLE_S_LEVELS = (100, 300, 600)
+IDLE_S_MM = 5.0
+IDLE_S_FEED = 300
+JOB_IDLE_S = ["G91", "G21", "M3"]
+for _i, _s in enumerate(IDLE_S_LEVELS):
+    JOB_IDLE_S.append("S%d" % _s)
+    JOB_IDLE_S.append("G1 X%g F%d" % (IDLE_S_MM if _i % 2 == 0 else -IDLE_S_MM,
+                                      IDLE_S_FEED))
+JOB_IDLE_S.append("M5")
+
+
+# Session J: the bench ladder's shape. M5 executes with the planner
+# drained and the kernel run over, and the rapids that follow start a
+# new run; the core issues no per-segment laser update for moves made
+# with the spindle off, so the stream's wanted state is all that decides
+# whether those rapids fire. A bare G0 with no M3 since the M5 is the
+# same case one step further.
+M5_IDLE_MM = 5.0
+M5_IDLE_FEED = 600
+M5_IDLE_TICKS = M5_IDLE_MM / (M5_IDLE_FEED / 60.0) * 28160
+JOB_M5_IDLE = [
+    "G91", "G21",
+    "M3 S500",
+    "G1 X%g F%d" % (M5_IDLE_MM, M5_IDLE_FEED),
+    WAIT_IDLE, ("sleep", 0.5),
+    "M5", ("sleep", 0.5),
+    "G0 X%g" % -M5_IDLE_MM, "G0 Y1",
+    WAIT_IDLE,
+    "G0 X%g" % M5_IDLE_MM,
+    WAIT_IDLE,
+    "M3 S500",
+    "G1 X%g" % -M5_IDLE_MM,
+    WAIT_IDLE, ("sleep", 0.5),
+    "M5",
+]
+
+
+# Session K: two jobs in one controller process, the second at the level
+# the first ended at. M2 leaves S modal and resets the motion mode to G1,
+# so the next job's M3 executes at that S; the core records it and issues
+# no per-segment update for a G1 at the same level, so the set_state is
+# the only thing that can light it. The parser starts in G0, which is why
+# a process's FIRST job never shows this: its M3 runs at rpm 0.
+JOB_NEXT = [
+    "G91", "G21", "M3", "S500",
+    "G1 X%g F%d" % (M5_IDLE_MM, M5_IDLE_FEED),
+    WAIT_IDLE, ("sleep", 0.5),
+    "M5", "G0 X%g" % -M5_IDLE_MM, "G0 Y1",
+    WAIT_IDLE, "G90", "M2", ("sleep", 1.0),
+]
+
+
 def fail(msg):
     print("FAIL: %s" % msg)
     sys.exit(1)
@@ -636,7 +744,7 @@ def main():
     rendered = check_density("density", dens, DENSITY_LEVEL, DENSITY_PERIOD,
                              DENSITY_MIN_TICKS)
     check_termination("density", dens)
-    if "laser armed (density, floor 0 %)" not in run_session.text:
+    if "laser armed (density, floor 0 %, curve off)" not in run_session.text:
         fail("[density] the arm did not select the density model at floor 0")
     print("PASS [density]: %d bytes, %d power bytes all at full duty, "
           "level->density %s"
@@ -746,13 +854,41 @@ def main():
     expect_levels = tuple(duty_for(x) for x in LADDER_S)
     check_density("floor-derived", floored, expect_levels, DENSITY_PERIOD,
                   DENSITY_MIN_TICKS)
-    if "laser armed (density, floor %g %%)" % PWM_MIN_PCT not in run_session.text:
+    if "laser armed (density, floor %g %%, curve off)" % PWM_MIN_PCT not in run_session.text:
         fail("[floor-derived] the arm report does not name the derived floor "
              "(text: %r)" % run_session.text[-400:])
     print("PASS [floor-derived]: a typed $35=0 is overwritten at the arm; the "
           "ladder renders through the %g %% floor key, levels %s"
           % (PWM_MIN_PCT, list(expect_levels)))
 
+    # --- rule 19: the dose curve bends S onto delivered light -----------
+    cur = run_session("curve", JOB_CURVE, conf=DENSITY_CONF_CURVED)
+    if "curve bench-default" not in run_session.text:
+        fail("[curve] the arm does not name the bench-default curve (text: %r)"
+             % run_session.text[-300:])
+    floor_frac = PWM_MIN / float(PWM_PERIOD)
+    expect = []
+    for s_val in CURVE_S:
+        d = curve_density_for(s_val)
+        expect.append(min(1.0, max(d, floor_frac)))
+    ticks = tick_bytes(cur)
+    spans = fire_spans(ticks)
+    if len(spans) != len(CURVE_S):
+        fail("[curve] %d fire spans, expected %d" % (len(spans), len(CURVE_S)))
+    got = []
+    for (a, b) in spans:
+        seg = ticks[a:b]
+        got.append(sum(1 for t in seg if t & 0x10) / float(len(seg)))
+    for g, w, s_val in zip(got, expect, CURVE_S):
+        if abs(g - w) > max(0.012, w * 0.06):
+            fail("[curve] S%d rendered density %.4f, expected %.4f through the "
+                 "bench-default curve" % (s_val, g, w))
+    if not all(b > a for a, b in zip(got, got[1:])):
+        fail("[curve] densities not monotonic: %s" % [round(g, 4) for g in got])
+    check_termination("curve", cur)
+    print("PASS [curve]: S %s -> densities %s through the bench-default curve "
+          "(floored at %.3f)" % (list(CURVE_S), [round(g, 3) for g in got], floor_frac))
+
     print("PASS: all stream emission rules hold")